1
INSTALLATION INSTRUCTIONS
856.768.8300 • TechSuppor[email protected]
GlowShift Gauges, LLC • 444 Commerce Lane Suite A • West Berlin, NJ 08091 • GlowShift.com
• Water Temperature Gauge
• 1/8-27 NPT Water Temperature Sensor
• Power & Sensor Harnesses
• Mounting Bracket
• Gauge Visor
1. There are several dierent ways to connect a Water
Temperature Gauge to your vehicle. In some cases an
adapter is needed to adapt the 1/8-27 NPT Sensor.
Note: If you install the sensor after the vehicles
thermostat, the gauge will not display a reading
until the vehicle thermostat has been opened.
• Coolant Fluid Port: Identify a coolant uid port
located on your engine and remove the port plug.
Directly install the water temperature sensor to the
coolant port. Additional adapters may be required if
the coolant port is not threaded to 1/8-27 NPT.
• Stock Sensor Location: Use a T-tting to “T” o your
stock sensor location. This will allow you to keep your
stock sensor installed, while also allowing you to install
an aftermarket temperature sensor.
The following instructions are for the installation of your Water Temperature Gauge. Before you
begin, lay out all items and ensure there are no missing parts. If any items are missing, please STOP
immediately and contact GlowShift Gauges.
7 Color Water Temperature Gauge
Wire Schematic
Disconnect negative battery terminals before starting any work on the vehicle.
• Water Temp Adapter: Please take a look at
www.GlowShift.com for available adapters including
Thread Adapters and T-Fittings. We also oer several
dierent-sized Water Sender Hose Attachment
adapters ranging from 13mm-52mm. Simply measure
the inside diameter of your radiator hose and install in
between two cut halves, securing it with the supplied
hose clamps.
2. To install the Water Temperature Sensor, start by applying
Teon tape to the Water Temperature Sensor threads.
Install the 1/8-27 NPT Water Temperature Sensor to your
vehicle’s system using one of the mentioned methods
that will work best for your application. Tighten the sensor
using a 14mm wrench.
3. Plug the Water Temperature Harness into the back of the
gauge.
Grommet
4. Route the Green Signal Wire through the engine bay and
rewall using a grommet, keeping it clear of any moving
parts and heat sources.
5. Splice the Green Wire from the gauge to the White Wire
of the water temperature sensor. Use an 18ga automotive
grade wire to extend if necessary.
6. Connect the Black Wire of the water temperature sensor
to any good, clean ground connection. You may also route
a wire directly to the negative side of the vehicle’s battery.
7. Before starting the vehicle be sure to rell the system
following the manufacturer’s recommended procedures.
STOP
Revised Mar 2020
Yellow: 12v Constant Source (+)
Red: 12v Ignition Switched Source (+)
Orange: 12v Headlight Switched Source (+)
Black: Vehicle/Engine Ground (-)
What’s Included
2
INSTALLATION INSTRUCTIONS
856.768.8300 • TechSuppor[email protected]
GlowShift Gauges, LLC • 444 Commerce Lane Suite A • West Berlin, NJ 08091 • GlowShift.com
Gauge Wiring
1. In order to test for power, reconnect the Negative Battery
Terminal.
2. It may be necessary to remove the Vehicle Trim and/or Kick
Panels in order to gain access to the vehicle’s Fuse Box.
3. Using a test light, locate a constant 12-Volt power source in
the vehicle’s fuse panel that receives 12- Volt power when
the ignition is turned o. You can splice into the circuit or
use an optional Expandable Circuit. Connect the Yellow
Wire of the gauge to the Constant 12-Volt Power Source.
4. Repeat the same step for the Red Wire of the gauge to
locate an Ignition Switched 12-Volt Power Source. This
source should not have any power with the key turned o
and have 12 Volts with the key turned on.
5. Connect the Orange Wire of the gauge to the positive
Headlight Switch Power Source using a Splice Connector,
either in the fuse box or at the switch itself.
Note: Make sure the connection source does not
dim. If the voltage is reduced when you lower the
Dimmer Wheel it will cause the gauges to icker
from not having enough voltage.
Orange 12v
Head Lamp
Yellow 12v
constant
red 12v switch
6. Locate a clean, reliable grounding source and connect the
Black Wire from the gauge.
7. After all wiring is complete, turn the vehicle’s key to the
“On” position and conrm that your gauge illuminates.
8. Press the COLOR Changing Button on your gauge and
scroll through the 7 Color options as well as the Color
Change and Color Fade option: this will allow you to
have the Gauge Face change between all of the colors
automatically.
9. Turn on the headlights to ensure that the gauge is
dimming.
10. Reinstall any panels that may have been removed.
11. Ensure your gauge is functioning properly.
Additional Information
• The supplied optional gauge visor is intended to be placed on the gauge so that the thickest part is at the top, creating a
cover over the gauge to help keep sun glare o of the gauge face.
• The included mounting bracket is designed to be used on a universal-style mount in order to keep the gauge secure. In
some cases one or both legs of the bracket may need to be modied to t the thickness and contour of the mount. Our
A-pillar gauge pods do not require the use of the mounting bracket but can be used if you desire, and there is enough
space to t it between the gauge and the gauge pod. When installing the bracket onto the gauge, make sure not to over-
tighten as it could pull the rear studs on the back of the gauge and damage it.
• GlowShift Gauges Installation Instructions: Installation documents are solely to provide a guide for individuals that are
mechanically and electronically able to install products. If you are unsure about the correct procedure for the installation of
a product, you should consult a licensed professional.
3
INSTALLATION INSTRUCTIONS
856.768.8300 • TechSuppor[email protected]
GlowShift Gauges, LLC • 444 Commerce Lane Suite A • West Berlin, NJ 08091 • GlowShift.com
ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY & DISCLAIMER
GlowShift Gauges, LLC (“GlowShift”) warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be
free from defects in material or workmanship for a period of one (1) year from the purchase date.
For a period of one (1) year from the date of purchase, at no charge to the Purchaser, GlowShift will repair or replace this Product if it is determined by GlowShift to
be defective. After the warranty period, the Purchaser must pay all charges for parts and labor.
Coverage under this warranty is only valid within the United States, including its territories, as well as in certain other countries. Purchasers should check our
website, www.GlowShift.com, to determine the warranty coverage in the countries in which they are located.
GlowShift does not warrant the installation of the Product, which is the sole responsibility of the Purchaser. Installation should be done by licensed professionals.
Improper installation may cause damage to the Product and any vehicle in which it is installed, and may cause burns and electrical injury to individuals. GlowShift’s
warranty does not cover any expenses incurred in removing Products that are defective or re installing replacement Products in their place.
During the warranty period, to have the Product repaired or replaced, the Purchaser must return the Product, freight prepaid by the Purchaser, to GlowShift (but for
customers in the contiguous United States, GlowShift will pay the shipping charges if any Product fails during the rst thirty (30) days after purchase). The Product
must be returned in its original carton or in a similar package aording an equal degree of protection. GlowShift will return the repaired or replaced Product,
freight prepaid, to the Purchaser. GlowShift does not provide Purchasers with temporary replacement units during the warranty period or at any other time.
This limited warranty is non transferrable and will automatically terminate if the original retail consumer purchaser resells the Product or transfers the vehicle in
which the Product is installed. An “original retail consumer purchaser” is a person who originally purchases the Product, or a gift recipient of a new Product that is
in its original packaging and unopened.
This limited warranty is subject to all of the following terms and conditions:
TERMS & CONDITIONS
1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: If Purchaser believes that a Product is defective in material or workmanship, written notice with an
explanation of the claim shall be given promptly by Purchaser to GlowShift. All warranty claims must be made within the warranty period, and any Products
returned to GlowShift must be shipped in accordance with GlowShift’s procedures (including use of RMA numbers supplied by GlowShift after notication). The
repair or replacement of any Product or part thereof shall not extend the original warranty period. The specic warranty on the repaired part only (not including
gauge sensors) shall be in eect for a period of ninety (90) days following the repair or replacement of that part, or the remaining period of the Product warranty,
whichever is greater. GlowShift does not provide a warranty on replacement gauge sensors.
2. EXCLUSIVE REMEDY; ACCEPTANCE: Purchaser’s exclusive remedy and GlowShift’s sole obligation is to supply (or pay for) all labor necessary to repair any
Product found to be defective within the repair or replacement fails to remedy the defect. Purchaser’s failure to make a claim as provided in paragraph 1 above or
continued use of the Product shall constitute an unqualied acceptance of such Product and a waiver by Purchaser of all claims thereto.
3. EXCEPTIONS TO LIMITED WARRANTY: GlowShift shall have no obligation to Purchaser with respect to any Product that is subjected to any of the following:
abuse, improper use, negligence, accident, modication, failure to follow the operating procedures outlined in the user’s manual, failure to follow the maintenance
procedures in the service manual for the Product, attempted repair by non qualied personnel, operation of the Product outside of the published environmental
and electrical parameters, or if the Product’s original identication (trademark, serial number) markings have been defaced, altered, or removed. GlowShift
excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS. GlowShift also excludes from warranty coverage any consumable items such as
fuses and batteries.
All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where
expressly provided otherwise in any documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE; REGISTRATION: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty
eligibility. Registration of any Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty.
DISCLAIMER OF WARRANTY
EXCEPT FOR THE FOREGOING WARRANTIES, GLOWSHIFT HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF
INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2 312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE.
LIMITATION OF LIABILITY
THE LIABILITY OF GLOWSHIFT, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS
OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT FOR WHICH
SUCH CLAIM IS MADE. IN NO EVENT SHALL GLOWSHIFT BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF
ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS
OR FOR ANY OTHER REASON WHATSOEVER.
GOVERNING LAW: This non transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America,
excluding their conicts of laws principles. The courts of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this
warranty.
This limited warranty gives specic legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or
countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are
advised to consult applicable state or country laws for a full determination of rights.
