MESA

From 4-35 lbs

USA

UPPAbaby, 276 Weymouth Street, Rockland, MA 02370 | uppababy.com | 1.844.823.3132

Model 1017-MSA-US | Version 3

are correct at time of print. UPPAbaby reserves the right to change anything at any time without prior notice.

Color representation is as close as print processes allow. Not all colors available at all retailers.

V3-122218

TABLE OF CONTENTS

BEFORE YOU BEGIN 3

CERTIFICATION 3

USE RECOMMENDATIONS 3

REGISTRATION 4

NOTICE OF EXPIRATION 4

WARNINGS + GENERAL SAFETY INSTRUCTIONS 5

VEHICLE COMPATIBILITY 14

CHOOSING A VEHICLE SEATING LOCATION 14

DETERMINING BEST INSTALLATION METHOD 15

BASE INSTALLATION 15

CARRIER INSTALLATION WITHOUT BASE 15

OVERVIEW OF LATCH 16

OVERVIEW OF VEHICLE SEAT BELT SYSTEMS 17

UNSAFE VEHICLE SEAT BELT SYSTEMS + SEATING 18

BASE INSTALLATION WITH LOWER ANCHORS 19

LEVELING BASE 19

BASE INSTALLATION WITH LOWER ANCHORS 20

SAFETY CHECK 21

UNINSTALLING BASE 21

BASE INSTALLATION WITH VEHICLE SEAT BELT 22

LEVELING BASE 22

SECURING THE BASE WITH VEHICLE SEAT BELT 22

SECURING THE BASE (LAP AND SHOULDER BELT INSTALLATION) 23

SECURING THE BASE (LAP BELT ONLY INSTALLATION) 24

SAFETY CHECK 25

UNINSTALLING BASE 25

REAR-FACING SEAT FEATURES 10

OVERVIEW OF BASE 10

OVERVIEW OF CARRIER 12

Read all instructions before use of the rear-facing car seat.

Keep instruction book for future use.

(Storage pocket located on underside of base.)

3 UPPAbaby MESA Instruction Book

TABLE OF CONTENTS

USE RECOMMENDATIONS

Children should remain rear-facing for as long as possible.

UPPAbaby

and the American Academy of Pediatrics

advise parents to keep

their toddlers in rear-facing car seats until age 2, or until they reach maximum

height and weight for their seat. Do not use this child restraint beyond the

expiration date or if the child outgrows either the weight or height requirements.

This child restraint is for use by children who meet BOTH requirements below:

WEIGHT REQUIREMENTS: 4-35 lbs (1.8-15.9 kg)

Includes Infant Insert recommended for use with infants weighing 4-8 lbs

(1.8-3.6 kg)

HEIGHT REQUIREMENTS: 32 in (81.3 cm) or less

This child restraint system conforms to all applicable Federal

Motor Vehicle Safety Standards (FMVSS).

This child restraint is certied for aircraft use. UPPAbaby and

the Federal Aviation Administration (FAA) strongly urge you to

secure your child in a child restraint system (CRS) or device for

the duration of your ight.

CERTIFICATION

The top of the child’s

head should not be less

than 1 in from the top

of the headrest when

in its highest position.

Harness should be at

the shoulders or slightly

below.

Retainer clip must be

at armpit level

and

harness straps should

be snug

BEFORE YOU BEGIN

CARE + MAINTENANCE 41

SIP PADDING REMOVAL 41

SEAT PADDING REMOVAL 42

SEAT PADDING INSTALLATION 44

SIP PADDING INSTALLATION 46

CLEANING 47

LIMITED WARRANTY 48

GENERAL USE 31

HARNESS BUCKLE POSITIONING 31

INFANT INSERT (RECOMMENDED 4-8 LBS) 32

SIP CARRIAGE + HARNESS POSITIONING 32

SECURING YOUR CHILD 33

PINCH TEST 34

ATTACHING CARRIER TO BASE 35

RELEASING CARRIER FROM BASE 35

HIDE-AWAY CANOPY 36

CARRY HANDLE 36

IMPORTANT CHECKS 37

CARRIER INSTALLATION WITH VEHICLE SEAT BELT 26

LEVELING THE CARRIER 26

DETERMINING BEST INSTALLATION METHOD 26

LAP/SHOULDER BELT STANDARD ROUTING METHOD 27

INSTALLATION WITH LOCKING CLIP 28

LAP BELT ONLY ROUTING METHOD 29

SAFETY CHECK 29

AIRCRAFT INSTALLATION 30

STROLLER COMPATIBILITY 38

FITTING CARRIER TO STROLLER FRAME 38

RELEASING CARRIER FROM STROLLER FRAME 38

FITTING ADAPTERS TO VISTA 2014 AND EARLIER FRAME 39

FITTING CARRIER TO VISTA 2014 AND EARLIER FRAME ADAPTERS 40

RELEASING CARRIER FROM VISTA 2014 AND EARLIER FRAME ADAPTERS 40

4 5 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

UPPAbaby reserves the right to make design changes and improvements

to any of our products as part of our commitment to innovation.

REGISTRATION

Please register your child restraint by lling out and

sending the postage-paid registration card that came

with your child restraint OR register online at:

www.uppababy.com/registration/carseat

Child restraints can be recalled for a variety of safety reasons. You must

For recall information, call the U.S. Government’s Vehicle Safety Hotline

at 1-888-327-4236 (TTY: 1-800-424-9153), or go online to www.nhtsa.gov.

TAKE A MOMENT TO FILL OUT THE FOLLOWING INFORMATION:

Information can be found on the manufacture labels or engraved on the

underside of the carrier.

Serial Number:

Date of Purchase:

Discontinue use of this

child restraint after 7

years from the date of

manufacture or after

a crash. Refer to labels

on bottom of Carrier

and Base.

NOTICE OF EXPIRATION

CARRIER BASE

BEFORE YOU BEGIN

WARNINGS + GENERAL SAFETY INFORMATION

WARNING

DEATH OR SERIOUS INJURY CAN OCCUR

BEFORE YOU BEGIN

According to accident statistics, children are

safer when properly restrained in the rear seating

positions than in the front seating positions.

Child restraint systems should be securely belted

to the vehicle, even when they are not occupied,

since in a crash an unsecured child restraint system

may injure other occupants.

Use only in rear-facing position when using it in

the vehicle.

NEVER place this child restraint on

a front seat with an airbag. DEATH

OR SERIOUS INJURY can occur.

An airbag can strike a rear-facing infant

restraint with enough force to crack the shell and

seriously injure or kill an infant. The back seat is

the safest place for children 12 and under. Refer

to the vehicle owner's instruction book before

installing this child restraint in a seating position

with side airbags.

6 7 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

WARNINGS + GENERAL SAFETY INFORMATION

Snugly adjust the belts provided with this child

restraint around your child. A snug strap should not

allow any slack. It lies in a relatively straight line

without sagging. It does not press on the child’s esh

or push the child’s body into an unnatural position.

SUFFOCATION HAZARD: Infant carrier can roll over

on soft surfaces and suffocate child. NEVER place

carrier on beds, sofas, or other soft surfaces.

Children have STRANGLED in loose

or partially buckled harness straps.

Fully restrain the child even when

carrier is used outside the vehicle.

•

NEVER leave child in carrier when straps are

loose or undone.

•

NEVER place carrier near window where cords

from blinds or drapes can strangle a child.

•

NEVER hang strings on or over the carrier or

attach to handle.

BEFORE YOU BEGIN

WARNINGS + GENERAL SAFETY INFORMATION

•

NEVER place items with a string around a child’s

neck, such as hood strings, pacier cords, etc.

FALL HAZARD: Child’s movement can slide carrier.

•

NEVER place carrier on counter tops, tables,

or any other elevated surfaces. DO NOT use on

shopping carts.

SAFETY WARNINGS:

Failure to follow these instructions could result in

serious injury to your child or other vehicle occupants.

•

NEVER leave child unattended.

•

DO NOT use the carrier or base if it is damaged or

broken, expired (over 7 years from date of manufacture),

missing instructions, missing parts, or if the straps are

cut, frayed, or damaged in any way.

•

DO NOT use this child restraint system if it has

been in a vehicle accident.

•

DO NOT use clothing or blankets that interfere

with fastening or tightening the harness. INSTEAD

place a blanket over the child after being properly

secured in the harness.

BEFORE YOU BEGIN

WARNING

8 9 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

WARNINGS + GENERAL SAFETY INFORMATIONWARNINGS + GENERAL SAFETY INFORMATION

SAFETY WARNINGS:

•

DO NOT use any accessories, pads or products

supplied by other manufacturers with this child

restraint, unless approved and tested by UPPAbaby.

Items not tested with this restraint could injure

your child.

•

DO NOT place carrier on top of shopping cart.

Carrier will not be secure and could fall causing

injury to child.

•

ALWAYS keep child properly harnessed when child

is in carrier.

•

ALWAYS check all surfaces of restraint before

securing your child. In warm weather, child restraints

can become very hot.

•

ALWAYS properly store lower anchor connectors

when not in use.

BEFORE YOU BEGIN

SAFETY WARNINGS:

•

DO NOT use this child restraint if the top of the

child’s head is less than 1 in from the top of the

headrest when in its highest position.

•

DO NOT use this child restraint in a vehicle seating

position where it cannot be tightly secured.

•

DO NOT install in rear-facing or side-facing

vehicle seats.

•

DO NOT modify this restraint except as instructed

in this instruction book. Minor modications can

change the way a child restraint performs in a crash.

•

DO NOT carry by the canopy.

•

DO NOT leave loose objects, e.g. cups, toys, bags,

umbrellas, etc., in the vehicle because they can

become deadly projectiles in a crash.

•

DO NOT take child out of the child restraint while

the vehicle is moving.

•

DO NOT allow children to play with this child

restraint. It is not a toy.

BEFORE YOU BEGIN

10 11 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

LEVEL WHEN

NO RED

VISIBLE

OVERVIEW OF BASE

REAR-FACING SEAT FEATURES

OVERVIEW OF BASE

LEVEL ADJUST

BUTTON

TIGHTNESS

INDICATOR

LOWER

ANCHOR

CONNECTORS

LOWER

ANCHOR

CONNECTOR

WEBBING

VEHICLE BELT

GUIDES (2)

VEHICLE BELT

LOCK-OFF

(CLOSED)

LOWER ANCHOR CONNECTOR

RELEASE BUTTONS (2)

LOWER

ANCHOR

CONNECTOR

STORAGE

VEHICLE BELT

LOCK OFF (OPEN)

MANUFACTURED/

EXPIRATION DATE

INSTRUCTION BOOK

STORAGE

LOCKING CLIP

ADJUSTMENT

FOOT

LEVEL ANGLE

INDICATORS (2)

REAR-FACING SEAT FEATURES

12 13 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

VEHICLE

SEAT BELT

GUIDES (2)

CARRIER RELEASE

FROM BASE

CARRIER RELEASE

FROM STROLLER

HARNESS

ANCHORS (2)

CROTCH BUCKLE

POSITIONS (2)

HARNESS ADJUSTER

STRAP HOLDER

CARRY HANDLE

ADJUSTMENT

BUTTONS (2)

STROLLER

ATTACHMENT

OVERVIEW OF CARRIER

RETAINER

CLIP

SIDE IMPACT PROTECTION (SIP)

(SIP) ADJUSTER TAB

HARNESS

COVERS (2)

HARNESS

STRAPS

HARNESS

HOLDER

POCKETS (2)

HIDE-AWAY

CANOPY

BUCKLE

LATCH

PLATES (2)

BUCKLE

INFANT INSERT

(RECOMMENDED

BETWEEN 4-8 LBS)

HARNESS

ADJUSTER

STRAP

HARNESS

ADJUSTER

RELEASE

OVERVIEW OF CARRIER

REAR-FACING SEAT FEATURES

MANUFACTURED/

EXPIRATION DATE

14 15 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

VEHICLE COMPATIBILITY

CHOOSING A VEHICLE SEATING LOCATION

PLEASE READ THE FOLLOWING INFORMATION

BEFORE INSTALLING THIS CHILD RESTRAINT!

Always park on a level surface when installing a

child restraint.

The safest seating position is one that works

best for your specic car seat, family and vehicle.

When determining whether the MESA Rear-Facing

Car Seat can be used with lower anchors in the

rear center seating position, it is critical that you

refer to your vehicle owner's instruction book. If

the MESA does not install best in the rear center

seating location, it is recommended to move to

one of the outboard seating positions.

Before installing this child restraint

you must determine the method

of installation and the best vehicle

seating position for that method.

This child restraint can be installed

either using LATCH or the

Vehicle Seat Belt.

LOWER

ANCHORS

VEHICLE

SEAT BELT

RETRACTOR

VEHICLE

SEAT BELT

DETERMINING BEST INSTALLATION METHOD

BASE INSTALLATION

CARRIER INSTALLATION WITHOUT BASE

At this point take out your VEHICLE OWNER'S INSTRUCTION BOOK.

You will need this to look up different features in your vehicle that might

affect the installation.

WARNING!

NEVER place a rear-facing only child restraint in front

of an active airbag.

Lap/Shoulder Belt

Installation (pg. 22)

Lower Anchor

Installation (pg. 19)

Lap/Shoulder Belt

Standard

Routing Method

(pg. 26)

Lap Belt Only

Routing Method

(pg. 26)

Lap Belt Only

Installation (pg. 22)

NOTE: The carry

handle must be locked

in any (3) positions

when in use (p. 29).

16 17 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

SEWN-ON LATCH PLATE

OVERVIEW OF VEHICLE SEAT BELT SYSTEMS

If you do not use lower anchor to properly secure the child restraint you

must use the Vehicle Seat Belt System. Seat belt systems vary by make,

model, and year of your vehicle. There are some vehicle belts that will NOT

work with this child restraint or that require additional steps.

CHECK YOUR VEHICLE OWNER’S INSTRUCTION BOOK

for information regarding your vehicle seat belt system(s).

This child restraint is compatible with most vehicle seat belt systems.

VEHICLE SEAT (LAP/SHOULDER BELT)

SLIDING LATCH PLATE

LOCKING LATCH PLATE LOCKING LATCH PLATE

VEHICLE SEAT (LAP ONLY BELT)

WEBBING

LATCH PLATE

BUCKLE BUCKLE

OVERVIEW OF LATCH

Most vehicles manufactured after September 1, 2002 are equipped

with LATCH (Lower Anchors and Tethers for CHildren). Check your

vehicle owner’s instruction book to determine lower anchor compatible

seating positions.

NOTE: No tether is required with this rear-facing carrier. Only lower

anchors are used.

OUTBOARD

LOWER

ANCHORS

INBOARD

LOWER

ANCHORS

OUTBOARD

LOWER

ANCHORS

22"=

NOTE: In order to use the rear center seating position with lower anchor,

the distance between the lower anchors may be up to 22 in and the seating

position must be approved by the vehicle manufacturer. If spacing between the

lower anchors is greater than 22 in or if the seating position is not approved by

the vehicle manufacturer then use the vehicle seat belt for installation.

VEHICLE COMPATIBILITY

LATCH PLATELATCH PLATE

WEBBING

BUCKLE

WEBBING

LATCH PLATE

BUCKLE

22"=

18 19 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

LEVEL WHEN

NO RED

VISIBLE

LEVEL WHEN

NO RED

VISIBLE

1 2

X XX

X X

LEVELING BASE

STEP 1: Place the base on the vehicle seat with the adjustment

foot toward the vehicle seat back.

STEP 2: Press the level adjust button on the top of the base

to extend the foot and change the recline angle. Check the

angle indicators on either side of the base. The base is level

when only the green marker is visible between the two arrows.

No red should be visible.

NOTE: Vehicle must be parked on a level surface to properly

level the base.

NOTE: If proper angle cannot be

achieved with adjustable foot, pool

noodles or a rolled towel may be used.

Foot must be in fully extended position.

UNSAFE VEHICLE SEAT BELT SYSTEMS + SEATING

WARNING

DEATH OR SERIOUS INJURY CAN OCCUR

Lap belts with emergency

locking retractor

Motorized (automatic) Lap/Shoulder with

two retractors

Inatable

Vehicle seats that face

side of the vehicle

Door mounted

Vehicle seats that face rear of the vehicle

DO NOT use this child restraint with the following vehicle seats:

BASE INSTALLATION WITH LOWER ANCHORS

CHECK YOUR VEHICLE INSTRUCTION BOOK

for information regarding your vehicle seat belt system(s).

Not all vehicle seat belts work with this child restraint.

DO NOT use this child restraint with the following seat belt systems:

VEHICLE COMPATIBILITY

20 21 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

LEVEL WHEN

NO RED

VISIBLE

LEVEL WHEN

NO RED

VISIBLE

1 2

3 4

SAFETY CHECK

UNINSTALLING BASE

STEP 1: Press the red button on the lower anchor connector while

pulling the connector off the vehicle anchor .

STEP 2: Store lower anchor connectors in designated housing found on

each side of the base.

BASE INSTALLATION WITH LOWER ANCHORS

STEP 3: Locate the lower anchor connectors on either side of the base and

remove by pushing the corresponding orange button on the top of the base

while pulling the connector out of the lower anchor storage pocket

STEP 4: Attach the lower anchor connectors to the vehicle lower anchors

located in the vehicle seat bight (crease of seat).

NOTE: Check lower anchor connectors are in the upright position.

BASE INSTALLATION WITH LOWER ANCHORS

STEP 5: Apply pressure rmly into the base allowing all the excess lower

anchor

connector webbing to retract and tighten.

NOTE: Push into the seat bight (crease of seat). Installation is complete

when tightness indicator turns from red to green and stays green when

downward push is discontinued.

• Base doesn’t move more than 1 in side to

side at the belt path .

• Ensure tightness indicator is green after

each use. If it is not, apply pressure by

pushing base into seat bight (crease of

seat) to tighten

• Lower anchor belts are secure and

untwisted

• Recline angle is correct. Base is level

when only green is visible between the

two arrows on the level indicator. No red

should be visible .

22 23 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

4A 5A 5A

LEVEL WHEN

NO RED

VISIBLE

LEVEL WHEN

NO RED

VISIBLE

1 2

SECURING THE BASE (LAP AND SHOULDER BELT INSTALLATION)

STEP 4A: Route the vehicle belt through the vehicle belt path while guiding

the lap portion of the belt as close as possible to the top of the lock-off

where the door hinges. Buckle the vehicle belt.

STEP 5A: Hold shoulder portion of belt above base. With one hand, push

down base in the direction of the seat bight (crease of seat) and hold rm

as you pull shoulder belt

. While holding taut, slide shoulder belt back

through the belt path as close as possible to the top of the lock-off .

NOTE: TIGHTNESS INDICATOR SHOULD

BE GREEN.

STEP 6A: Close the top section of

the lock-off over the lap/shoulder

belt . Second, close the bottom

section of the lock-off over the

belt . Make sure you push the

bottom of the lock-off all the way

down until you hear an audible click.

BASE INSTALLATION WITH VEHICLE SEAT BELT

STEP 1: Place the base on the vehicle seat with the

adjustment foot toward the vehicle seat back.

STEP 2: Press the level adjust button on the top of the base

to extend the foot and change the recline angle. Check the

angle indicators on either side of the base. The base is level

when only the green marker is visible between the two arrows.

No red should be visible.

NOTE: If proper angle cannot be

achieved with adjustable foot, pool

noodles or a rolled towel may be used.

Foot must be in fully extended position.

LEVELING BASE

BASE INSTALLATION WITH VEHICLE SEAT BELT

SECURING THE BASE WITH VEHICLE SEAT BELT

STEP 3: Open lock-off.

PROCEED TO:

Securing the Base (Lap and Shoulder

Belt Installation)–pg. 23, steps 4A-6A

Securing the Base (Lap Belt Only

Installation)–pg. 24, steps 4B-6B.

NOTE: Check that the base doesn’t move more than 1 in side to side at

the belt path. If movement is more than 1 in, twist the buckle and then

fasten the seat belt to help secure t.

24 25 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

LEVEL WHEN

NO RED

VISIBLE

LEVEL WHEN

NO RED

VISIBLE

STEP 4B: Route the vehicle belt

through the belt path while guiding

the lap portion of the belt as close

as possible to the topside of the

lock-off where the door hinges.

Buckle the vehicle belt.

STEP 5B: With one hand push down

base and hold rm as you pull lap

belt to tighten and remove any slack.

NOTE: TIGHTNESS INDICATOR

SHOULD BE GREEN.

STEP 6B: Close the top section

of the lock-off over the belt .

Second, close the bottom section

of the lock-off over the belt .

Make sure you push the bottom

of the lock-off all the way down

until you hear an audible click.

• Lock-off must be used at all times when

installing with a vehicle seat belt.

• Base doesn’t move more than 1 in side

to side at the belt path . If movement

is more than 1 in, twist the buckle and then

fasten the seat belt to help secure t.

• Ensure tightness indicator is green after

each use. If it is not, open lock-off then

tighten belt. When tightness indicator

turns green, close lock-off

• Belts are secure and untwisted

• Recline angle is correct. Base is level

when only green is visible between

the two arrows on the level indicator.

No red should be visible .

STEP 1: Unbuckle seat belt.

STEP 2: Open lock-off.

STEP 3: Remove seat belt.

SAFETY CHECK

SECURING THE BASE (LAP BELT ONLY INSTALLATION)

UNINSTALLING THE BASE

BASE INSTALLATION WITH VEHICLE SEAT BELT

NOTE: Before closing the lock-off door, make sure the vehicle seat belt

has not slipped down into the belt path and is as close as possible to the

topside of the lock-off where the door hinges.

NOTE: Check that the base doesn’t move more than 1 in side to side at

the belt path. If movement is more than 1 in, twist the buckle and then

fasten the seat belt to help secure t.

26 27 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

1 2

CARRIER INSTALLATION WITH VEHICLE SEAT BELT

STEP 1: Place the carrier rear-facing on the vehicle seat.

STEP 2: Make sure the vehicle is parked on level ground and the red line

on the carrier is level to the vehicle oor.

LEVELING THE CARRIER

DETERMINING BEST INSTALLATION METHOD

NOTE: For a more stable

installation, a pool noodle

or rolled towel may be used.

If your vehicle does not have the LATCH System in your preferred seating

position, the car seat must be secured to the vehicle using a vehicle seat

belt. The car seat with the base or without the base can be secured using

vehicle seat belts. There are two methods of carrier only installation:

LAP/SHOULDER STANDARD ROUTING METHOD: Installation with

both the lap and shoulder belt. (proceed to pg. 27)

LAP ONLY METHOD: No shoulder belt is used. This method applies

to vehicle with no shoulder belt and aircraft. (proceed to pg. 29)

LAP/SHOULDER BELT STANDARD ROUTING METHOD

STEP 1: Route the lap portion of

the seat belt through both lap belt

guides on the carrier, and buckle

the seat belt.

STEP 2: Lock vehicle seat belt.

NOTE: See vehicle owner's

instruction book for more

information on locking your seat

belt for child restraint installations.

WARNING!

Vehicle seat belt must

lock; otherwise a locking

clip must be used. See pg.

28 for instructions.

STEP 3: Push the carrier into the ve-

hicle seat bight (crease of the seat)

while pulling on the shoulder portion

of the seat belt closest to the buckle.

NOTE: Check that the carrier is still

properly leveled.

CARRIER INSTALLATION WITH VEHICLE SEAT BELT

28 29 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

CARRIER INSTALLATION WITH VEHICLE SEAT BELT

STEP 1: While pushing into the

child restraint, pull the seat belt

tight to eliminate any slack then

pinch both pieces of seat belt

webbing directly behind the latch

plate. Unbuckle the belt without

letting the webbing slip.

STEP 2: Thread the locking clip

onto both lap and shoulder belts

1 in from the latch plate.

STEP 3: Re-buckle the vehicle belt.

NOTE: The locking clip can be found on the underside of the base

(pg. 11). The locking clip can be used FOR CARRIER AND BASE installation

with Lap/Shoulder belt combination when the seat belt does not lock.

WARNING!

Vehicle seat belt must lock; otherwise a locking clip

must be used. See instructions below.

INSTALLATION WITH LOCKING CLIP

• Carrier doesn’t move more than 1 in side to side at the belt path .

• Belts are secure and untwisted.

• Angle is correct when the vehicle is parked on level ground and the

red line on the carrier is level to the vehicle oor

• Seating position is permitted by both UPPAbaby and your vehicle

manufacturer for use with the type of Vehicle Seat Belt.

• Carry handle is locked in any of the three (3) positions

SAFETY CHECK

LAP BELT ONLY ROUTING METHOD

STEP 1: Route the lap belt through both guides on the carrier, and buckle

the seat belt.

STEP 2: Push the carrier into the vehicle seat bight (crease of the seat)

while pulling on the loose portion of the lap belt closest to the buckle.

NOTE: Check that the carrier is still properly leveled.

LAP/SHOULDER BELT STANDARD ROUTING METHOD

CARRIER INSTALLATION WITH VEHICLE SEAT BELT

30 31 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

AIRCRAFT INSTALLATION

THIS CHILD RESTRAINT IS CERTIFIED FOR AIRCRAFT USE.

UPPAbaby and the Federal Aviation Administration (FAA)

strongly recommend that children up to 40 lbs (18 kg) use

a certied harnessed child restraint or other device approved

for aircraft travel.

When installing this child restraint on an airplane, install the

same way as Carrier Installation with Vehicle Seat Belt/

Lap Belt Only Routing Method (pg. 29).

IMPORTANT: Make sure that the aircraft buckle does not

interfere with the belt guides on the infant carrier.

IMPORTANT NOTES:

• Notify the airline ahead of time that you’ll be traveling with

a child restraint.

• Install this carrier in a window seat to avoid blocking the aisle.

• Ask for a seat belt extender if the lap belt is too short.

• Use only on a forward-facing aircraft seat.

• DO NOT use this restraint if a secure installation cannot be

achieved.

• Place carry handle in any of the (3) locked positions for use

in the aircraft as long as it doesn’t interfere with the back of

the seat in front of the carrier.

WARNING!

• DO NOT use base with aircraft installation.

Only the carrier is certied for aircraft use.

• Inatable seat belts are NOT compatible

with this child restraint.

GENERAL USE

CARRIER INSTALLATION WITH VEHICLE SEAT BELT

HARNESS BUCKLE POSITIONING

The crotch belt and buckle has two use positions. Always position the buckle

and crotch strap in the slot closest to the child. If the child is on top of the

buckle in the inner position, then adjust the buckle to the outer position.

STEP 1: Unbuckle the harness.

STEP 2: Flip carrier over, insert the metal clip

completely through the shell and seat pad.

STEP 3: Locate the appropriate buckle slot and

insert from the top completely through the

slot on the seat pad and shell.

STEP 4: Check that buckle is securely attached

by pulling up on buckle.

1 2

32 33 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

1 2

This child restraint has an adjustable head restraint and no-rethread harness

system that is easy to adjust to properly secure the child.

STEP 1: Adjust the head restraint by pulling on the adjuster tab and

sliding the head restraint up or down .

STEP 2: Position the head restraint so the harness rests at the child’s

shoulders or slightly below.

SIP CARRIAGE + HARNESS POSITIONING

GENERAL USE

SECURING YOUR CHILD

STEP 1: Loosen the harness by

pressing on the harness adjuster

release button and pulling out the

shoulder straps.

STEP 2: Open the retainer clip,

unbuckle the harness, and tuck

the latch plates into the side

pockets to hold harness open.

STEP 3: Place infant in child restraint

making sure their body is making full

contact with the seating surface.

Place harness over child and insert

buckle tongues into the buckle until

a “click” is heard. Pull up on the

buckle tongues to make sure they

are locked.

WARNING!

• DO NOT place rolled

towel or small blanket

between crotch of infant

and buckle or around

head or SIP carriage.

• NEVER use non-regulated

products with this child

restraint, unless approved

by UPPAbaby.

INFANT INSERT (4-8 LBS)

To ensure a better t for smaller infants, we

recommend using the infant insert (included)

between 4 and 8 lbs. Remove infant insert

when infant begins growing on top of the

buckle making it difcult to buckle harness.

NOTE: Never use non-regulated products with

this child restraint, unless approved by UPPAbaby.

34 35 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

SECURING YOUR CHILD

PINCH TEST

STEP 4: Pull up on the harness to

remove excess slack around the

child’s legs.

STEP 5: Pull the harness adjuster

strap to snugly adjust the harness

straps around your child.

STEP 6: Close retainer clip and

position at armpit level. Make sure

the shoulder pads don’t interfere

with positioning the chest clip.

HARNESS SHOULD BE SNUG.

Pinch harness webbing at child’s

shoulders. If you can pinch web-

bing, the harness is too loose

and should be tightened.

GENERAL USE

NOTE: For smaller babies, it is recommended to remove the harness pads

for a more secure t.

GENERAL USE

STEP 1: Place carrier on base

until a click is heard .

STEP 2: Check for a secure

connection by pulling up on

carry handle

STEP 1: Pull and hold carrier release

button on back of the carrier.

STEP 2: Lift carrier off base.

RELEASING CARRIER FROM BASE

ATTACHING CARRIER TO BASE

NOTE: Handle can be in any of the

three (3) locked positions for use in

the vehicle.

36 37 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

Hide-away canopy easily adjusts

to one of three (3) positions.

TO EXTEND CANOPY: Slowly

pull forward on main canopy frame

until resting in desired position.

TO RETRACT/STOW CANOPY:

Gently push downward on main

canopy frame allowing the center

support and canopy fabric to guide

into the storage compartment

in carrier.

HIDE-AWAY CANOPY

CARRY HANDLE

The carry handle must be locked in any three (3) positions when in use:

carry,

store and stand.

To adjust the carry handle position, squeeze both handle adjustment

buttons and rotate forward or backward.

WARNING!

NEVER hang toys and other objects from the carry handle

when using in the vehicle. These products have not been

tested by UPPAbaby and therefore are not approved for

use with this child restraint.

GENERAL USE

IMPORTANT CHECKS

• This child restraint is for rear-facing use only.

• The seat must be tightly installed in a forward-

facing vehicle seat.

• The harness should be at the shoulders or

slightly below

• Retainer clip must be at armpit level and

harness straps should be snug .

• The top of child’s head should not be less

than 1 in from the top of the headrest

when in its highest position.

• The child must weigh between 4 and 35

pounds and be no taller than 32 in.

• The back seat is the safest place for children

aged 12 and under.

• NEVER use non-regulated products with this

child restraint, unless approved by UPPAbaby.

• NEVER place in front of an active airbag.

• Install using lower anchor or the vehicle seat belt,

NOT BOTH.

• DO NOT secure an infant in the carrier with

extra material, bulky clothing, or extra padding.

Instead place a blanket over the harness after

properly securing the child .

• Carry handle must be locked in any of the

(3) handle positions.

• Adjust base to the appropriate angle by using the angle indicator on the

sides of the base or the level to ground line on the carrier.

• Always check the tightness indicator is green after each use.

• Always secure an unoccupied child restraint; in a crash an unsecured infant

car seat may injure occupants in your vehicle.

GENERAL USE

38 39 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

ATTACH

REMOVE

1 2

FITTING CARRIER TO STROLLER FRAME

Prior to tting MESA carrier to stroller frame,

engage brake on stroller and remove toddler seat from frame.

STEP 1: With carrier facing stroller

handle, align carrier handle hubs

with attachment posts on stroller.

STEP 2: Let carrier slide onto

attachment posts. An audible click

indicates proper attachment.

STEP 3: Lift up on car seat handle

to check attachment.

STEP 1: Engage and hold the stroller release button on the top of the

carry handle.

STEP 2: Lift the carrier off stroller frame.

RELEASING CARRIER FROM STROLLER FRAME

STROLLER COMPATIBILITY

NOTE: Compatible with VISTA 2015+ and CRUZ strollers.

STROLLER COMPATIBILITY

FITTING ADAPTERS TO VISTA 2014 AND EARLIER FRAME

TO ATTACH: Place adapters (logo facing out) onto seat attachments and

press until you hear a click.

TO REMOVE: Push down release button on backside of adapter and lift

up from stroller frame.

Prior to tting adapter to VISTA 2014 and earlier frame, engage brake

on stroller and remove toddler seat or bassinet from frame.

NOTE: VISTA 2014 and earlier stroller models require adapters for

use with the MESA. Please contact UPPAbaby Customer Service at

1.844.823.3132 for your free adapter.

NOTE: There are 2 adapters, one for the left and one for the

right side of the stroller. The adapters are marked with “L” and “R”

respectively. (The left adapter and left side of the stroller are

determined by the driver’s left.

NOTE: Indicators should appear green as conrmation of secure

installation. If the indicator symbol is red then the adapter is not

secure. Remove the adapter and try fastening it again.

40 41 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

1 2

FITTING CARRIER TO VISTA 2014 AND EARLIER

FRAME ADAPTERS

STEP 1: Engage and hold the stroller release button on the top of the

carry handle.

STEP 2: Lift the carrier off the adapters on stroller frame.

RELEASING CARRIER FROM VISTA 2014 AND EARLIER

FRAME ADAPTERS

STEP 1: With carrier facing

stroller handle, align carrier stroller

hubs with adapters on stroller.

STEP 2: Let carrier slide onto

adapter posts.

STEP 3: Lift up on carrier handle

to check attachment.

STEP 1: Unbuckle retainer clip and

harness.

STEP 2: Pull forward on SIP padding

releasing harness straps.

STEP 3: Pull SIP padding down from

bottom and release.

SIP PADDING REMOVAL

CARE + MAINTENANCE

STROLLER COMPATIBILITY

Following are fabric removal instructions for cleaning.

42 43 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

1 2

SEAT PADDING REMOVAL

STEP 1: Remove buckle cover.

STEP 2: Unhook harness adjuster

strap from underside of carrier.

STEP 3: Remove (4) plastic tabs

from front sides of carrier.

STEP 4: Loosen padding from front

end of carrier and free padding

from around harness adjuster

release button housing.

STEP 5: Raise SIP to highest position

and pull back padding panel.

CARE + MAINTENANCE

SEAT PADDING REMOVAL

STEP 6: Slide SIP to lowest

position and release (8) plastic

tabs from upper portion of carrier.

STEP 7: Thread SIP adjuster tab

through buttonhole in top of

seat pad.

STEP 8: Pull seat padding up and

forward to remove padding around SIP.

CARE + MAINTENANCE

44 45 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

3 4

SEAT PADDING INSTALLATION

STEP 1: With the SIP in the lowest position, lay seat pad over carrier, open

Velcro

ap and t opening around SIP/headrest.

STEP 2: Tuck lowest side tab behind seat foam and under post. Repeat on

other side.

STEP 3: Place second side tab into designated plastic slot and third side tab

behind seat foam. Repeat on other side.

STEP 4: Tuck top 2 tabs into designated slots and pull headrest adjuster tab

through buttonhole

CARE + MAINTENANCE

SEAT PADDING INSTALLATION

STEP 5: Lift lower part of SIP and pull harness straps to each side of opening.

Secure padding panel with Velcro

STEP 6: Raise SIP/headrest into highest position.

STEP 7: Pull harness adjuster strap through opening in seat pad and install

pad around adjuster release button housing.

STEP 8: Wrap padding around front lip and install 4 lower plastic tabs.

STEP 9: Reconnect harness adjuster strap.

46 47 UPPAbaby MESA Instruction Book UPPAbaby MESA Instruction Book

CLEANING FABRICS

Fabrics include: seat pad, infant inserts, buckle pads and shoulder pad.

Machine wash in cold

water on gentle cycle

with mild detergent.

Dry at and away

from direct sunlight

before re-use or

storage.

DO NOT bleach, iron

or dry clean.

CLEANING HARNESS WEBBING + CANOPY

Spot clean using

warm water with

mild detergent.

Air dry completely

before re-use or

storage.

DO NOT bleach or

iron.

CLEANING PLASTIC

Spot clean using

warm water with

mild detergent.

Towel dry com-

pletely before re-use

or storage.

DO NOT bleach.

CLEANING BUCKLE AND LOWER ANCHOR CONNECTOR HARDWARE

NOTE: Buckle should fasten with a “click” if not, rinse under warm running

water. DO NOT use detergents or lubricants.

STEP 1: Insert lower part of SIP

carriage into pocket on the back

of SIP padding.

STEP 2: Guide harness straps back

into slots in SIP padding.

STEP 3: Secure SIP cover tightly

around SIP ears.

SIP PADDING INSTALLATION

CLEANING

CARE + MAINTENANCE

48 UPPAbaby MESA Instruction Book

Welcome to the UPPAbaby family! We are with you for

the long haul. Register your car seat within three months

to claim your Limited Lifetime Warranty*.

*Lifetime warranty applies to UPPAbaby car seats and only

the original owner, within the lifetime of the product. To

receive your Limited Lifetime Warranty, you must register

your car seat within three months of purchase and provide a

valid purchase receipt from an authorized UPPAbaby retailer.

The “lifetime” of the product is dened as the period of use

by the registrant for use with his/her children up to 7 years

from date of manufacture.

Your UPPAbaby product is warranted to be free from any manufacturing defects for a

period of 2 years from the date of purchase under normal use and in compliance with

the operating instructions.

This warranty is not transferable and extends only to the original retail purchaser and is

only valid when supplied with proof of purchase. Please retain proof of purchase for this

limited warranty.

The warranty is valid only in the original country of purchase. This warranty is subject to

the conditions set forth by country in which the items were purchased. Conditions may

vary. UPPAbaby will not ship replacement or repair parts out of the country of purchase.

UPPAbaby will provide replacement parts or conduct repairs as determined tting by the

company. UPPAbaby reserves the right to exchange item with a replacement part. Some

parts may be replaced with newer model parts as the product is improved over time.

Please note that a repair issue will NOT be covered by this warranty if:

• The issue is caused by misuse or poor maintenance. Please refer to this instruction

book for guidance on car seat use and maintenance.

• Damage is caused by improper installation of UPPAbaby parts and/or accessories.

Please refer to this instruction booklet for guidance on car seat assembly and use.

• Damage is corrosion caused by lack of maintenance or service.

• Damage is due to general wear and tear, which is the result of everyday use or negligence.

• Damage is caused by sun intensity, sweat, detergents, damp storage or frequent washings.

• Repairs or modications are carried out by a third party.

• Product is purchased from an unauthorized retailer. Approved retailers are listed on our

website at uppababy.com.

• Product is second-hand.

• Product is damaged as a result of an accident, airline or freight damage.

UPPAbaby reserves the right to determine if warranty terms and conditions have been met.

Please contact your local distributor if you have any questions regarding warranty.

LIMITED WARRANTY

CARE + MAINTENANCE