2020 DECKING INSTALLATION GUIDE

2020 DECKING

INSTALLATION GUIDE

This symbol indicates text continues to next page.

What’s New for 2020:

Page 5 – Revised Care and Cleaning Guide

Page 12 – Revised decking- and fascia-recommended fasteners

Page 13 – Revised fascia installation recommendations

Page 18 – Revised width-to-width gapping (face-fastening)

Page 26 – Revised warranties

Need Help?

Trex provides a variety of valuable resources to answer your questions or concerns. For additional

assistance, check out:

Trex.com

Here you will ﬁnd a wealth of useful information on Trex’s extensive products including: installation,

care and cleaning instructions and videos, technical help, and FAQs. You’ll also ﬁnd inspiring photos of

deck projects, steps to help you plan and start your project, and tips for selecting the right deck builder.

At trex.com, you can request information, register your warranty, and reach out to customer service

representatives who can answer even more questions.

» Call 1-800-BUY-TREX (1-800-289-8739) and speak to a Customer Loyalty Advocate who can answer

your questions.

Refer to www.trex.com for up-to-date installation and technical documents that may not be found in this

printed guide.

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

Please visit our website at www.trex.com, and choose Literature at the top of the page,

to review individual installation instructions for speciﬁc Trex lighting, post mounts, joist

mount post, and all railing products.

This will ensure you are using the most up to date installation instructions with these

products.

To learn about Trex Signature

aluminum, and Transcend

and Select

railing products, visit www.trex.com/products/railing.

INSTALLATION GUIDE

Trex Installation Guide

CONTENTS

SECTION ONE: General Information

Safety ....................................................................................................... 4

Tools .........................................................................................................4

Care and Cleaning .............................................................................. 5

SECTION TWO: Planning Ahead

Trex

Decking ....................................................................................... 8

Railing (Including ADA Handrail) ................................................ 8

Trex

DeckLighting™ ......................................................................... 8

Trex RainEscape

Drainage System .......................................... 8

Installing Hot Tubs, Planters, and Seating ............................... 8

Installing Fireplaces and/or Fire Pits ......................................... 9

Installing a Pergola............................................................................. 9

Installing Trex Spiral Stairs™ .......................................................... 9

Installing Trex Outdoor Kitchens™ .............................................. 9

SECTION THREE: Decking

Decking, Fascia, and Fastener SKUs .....................................11

Decking and Fascia Recommended Fasteners ...............12

Trex Fascia Installation Recommendations .......................13

Framing and Fastening Tips .....................................................14

Rooftop and Sleeper Deck Systems .....................................15

Metal Framing Requirements and Gapping ......................16

Code Compliance ..........................................................................18

Gapping and Overhang ..............................................................18

How to Install Decking

Important Notes Before Installing Trex Decking ...............19

Routing Square Edged Boards for Trex Hideaway

Hidden Fasteners ..........................................................................19

Abutted Board Attachment Requirements ......................19

Installing Trex Transcend

, Enhance

, Select

Deck Boards .................................................................................. 20

Installing Trex Escapes

.............................................................21

Replacing Trex Boards ..............................................................23

Spanning Requirements For Trex Stairs ............................24

Installing Trex Stair Treads

Installed with Hidden Fasteners ........................................25

SECTION FOUR: Warranties

Trex Transcend, Trex Enhance, Trex Select, and Trex

Universal Fascia Limited Fade & Stain Warranty .................. 27

Trex

Limited Warranty .....................................................................29

Color Palette ........................................................................................31

GENERAL INFORMATION

Safety

When working on any construction project, you should

wear protective clothing and safety equipment. Wear

safety glasses, gloves, a dust mask and long sleeves,

particularly when cutting in conﬁned spaces.

Trex decking and railing are heavier and more ﬂexible

than wood. DO NOT try to lift the same quantity of

Trex boards as you would traditional lumber. Go to

www.trex.com for Safety Data Sheets (SDS).

Tools

SAWS

Miter Saw:

When using a miter

saw we recommend

using the Trex Blade™

or a carbide-tipped

blade with 60 teeth

or more. The Trex

Blade comes in three

different sizes and

is ideal for cutting

all Trex decking and

railing products (not

recommended for

Trex Elevations).

Jigsaw:

For detailed and/

or small cuts (ie:

cutting deck board to

ﬁt around a post), a

jigsaw with

a carbide-tipped

blade can be used.

DRILLS

Install Trex

recommended fasteners

with standard power

drills, impact drivers

(use care if using impact

drivers), or right angle

drills.

SPECIFIC DECK BOARD ATTACHMENT TOOLS

Screw Guns:

Some Trex recommended deck fasteners are compatible

with screw guns. Refer to the recommended fasteners

page for more information.

TigerClaw

Pneumatic Gun:

If choosing to use the

Trex Hideaway Hidden

Fastener Connector Clips

(these are the metal clips)

for Transcend or Enhance

Decking or the TigerClaw

TC-G Hidden Fasteners with

Trex Select Decking, the

TigerClaw pneumatic gun is a terriﬁc option that allows

for quicker install time.

Trex Router Bit:

Trex decking routs to give

extremely crisp edges when

using the Trex Router Bit

with standard router, and

can be use with all Trex

Hideaway Hidden Fasteners.

*Tiger Claw

is a registered trademark of Tiger Claw, Inc.

* Trex Blade™ is manufactured and sold by Freud Tools, Inc. under a

Trademark License Agreement with Trex Company, Inc.

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

GENERAL INFORMATION

Trex Transcend

, Trex Enhance

, and Trex Select

Care and Cleaning Guide

All exterior building materials require cleaning. Generally, soap and water is all that is required to clean Transcend,

Enhance, and Select products. For additional information, see below.

Problem Solution

Dirt and Debris

The affected area should be sprayed off with a hose to remove surface debris. Use warm

soapy water and a soft bristle brush to remove dirt and debris from the embossing pattern.

Using a Pressure

Washer (General

Cleaning Issues

)

A pressure washer with no greater than 3100 psi** that has a fan attachment/adjustment

and soap dispenser may be used to remove dirt or mud. Spray deck with soap, then follow

by gently scrubbing each deck board with a soft bristle brush. Spray/rinse each individual

deck board using a fan tip no closer than 8-in (203 mm) from the decking surface. RINSE

THOROUGHLY. If dirty water from cleaning is left to dry, a film will remain on the decking

surface.

Issues with Concrete,

Cement, Mortar, or

Stucco Dust

When working with cement, concrete, mortar, or stucco, protect the decking as

much as possible in order to not get dust particles on the decking surface. These

particles, once they get hot or wet, can cause a reaction on the decking surface

and are very difficult to remove. If particles get on the decking surface, Trex

recommends using Sakrete™ Concrete Dissolver (www.sakrete.com/products/

concrete-dissolver). BE SURE TO FOLLOW MANUFACTURER'S INSTRUCTIONS.

Hard Water Staining

Hard water is water with high amounts of mineral deposits like lime, silica and calcium.

When the water dries, deposits are left behind, leaving unsightly spots on surfaces. This is

not a defect of Trex products but an issue with the water itself. Generally, these deposits

can be cleaned with white vinegar on decking surfaces. Rinsing is required, so care should

be taken to not use hard water for this purpose. If hard water must be used, dry with a cloth

or use a blower to dry surfaces. In some cases a deck brightener product may also be used

to help clean hard water stains.

Chalk Lines

Most colored chalks are permanent and may discolor the surface. Use only Irwin

Strait-Line

Dust-Off Marking Chalk (purple), available at www.Irwin.com.

Tannins Due to Debris

Remove all debris from the deck using a hose or broom. Once the deck surface is dry, apply

a deck “brightener"* to the deck as directed by the manufacturer. Deck Brighteners contain

oxalic acid, which will also remove tannins.

Ice and Snow

A plastic shovel may be used to remove snow from the deck. Use calcium chloride or rock

salt to melt the snow and ice from the deck surface.

Oil, Grease, and Food

All food spills should be removed as soon as possible. The surface must be cleaned within

seven days to maintain the stain warranty. To remove, spray off with a hose and use warm,

soapy water and a soft bristle brush to remove spills from the embossing pattern.

Mold and Mildew

If debris such as pollen and dirt is allowed to remain on the deck surface, mold can feed on

the biofilm. Using a hose and warm, soapy water with a soft bristle brush is recommended

to remove the food source and mold.

GENERAL INFORMATION

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

Trex Transcend

, Trex Enhance

, and Trex Select

Care and Cleaning Guide

Problem Solution

Trex and Static

Electricity

While this is not common, static electricity can occur on walking surfaces in dry

climates or in areas where dry winds and dust-borne particles lay on the decking

surfaces. Static electricity can build up on occupants walking across any composite

decking surface, including Trex, then produce a small static shock if they touch a

grounded metal surface such as railing, door, etc.

This condition can be decreased greatly with the use of a product call ACL Staticide

Two products tested were General Purpose Staticide

and Heavy Duty Staticide

. Both

are effective in greatly reducing static electricity on Trex decking surfaces. Apply full

strength, using a mop on a dry decking surface, and allow to dry; no rinsing or diluting

needed. Products are non-toxic, non-ﬂammable, non-staining (will not change the color

of decking surface), completely biodegradable, and safe to use. Product is water-based

and may require a second application after rain or other weather conditions. Over a

period of time, the effect of static will dissipate naturally on the decking surface.

See link for more information on product:

www.aclstaticide.com/antistatic_coatings.html

Rubber Mats

Use caution when using rubber-backed mats (i.e. welcome mats, etc.) as these may

contain substances that can sometimes discolor or lighten the decking surface.

Curving Trex Decking

Trex recommends the use of the Trex

CustomCurve

to properly curve decking

products. Note that Trex Enhance decking cannot be curved.

Job Site Storage

Store decking on a ﬂat level surface and ALWAYS use proper supports (dunnage).

DO NOT store directly on the ground. When stacking decking bundles, supports

(dunnage) should start approximately 8-in (203 mm) from each end and be spaced

approximately 2-ft (0.61m) on center. In addition, supports (dunnage) should line up

vertically/perpendicular to the decking product. Adjust support blocks (dunnage)

accordingly if bundles are loose. For Select decking, Enhance decking, and 1x12 and

1x8 products, the maximum stack height is 12 bundles. For all other decking products

maximum stack height is 14 bundles (IMPORTANT TO NOTE THAT PROPER DUNNAGE

SPACING MUST BE IN PLACE FOR THESE HEIGHTS). When stacking multiple bundles,

ensure that dunnage lines up vertically down through each stack. ALWAYS cover

decking products on site until ready to be installed.

NOTES:

» Refer to www.trex.com to view a general care and cleaning video for Transcend, Enhance, and

Select decking.

» Refer to www.trex.com for a care and cleaning guide for Trex Early-Generation Composite and

PVC Decking.

Strait-Line

is a registered trademark of Irwin Industrial Tool Company.

Sakrete™ is a trademark of Oldcastle APG, a CRH Company.

*Use of products containing bleach or acid can lighten the lighten the surface of Trex. Use in an inconspicuous area to determine whether you

like the effect. Neither product will affect the structural integrity of Trex.

**Use of a pressure washer greater than 3100 psi could damage the boards and void the warranty.

PLANNING AHEAD

PLANNING

AHEAD

PLANNING AHEAD

Trex Decking:

» When installing any Trex decking product, especially

Trex Transcend Tropicals, it is a good idea to mix

and match all of the boards on the job site prior to

installation to ensure an appealing mix of light and

dark tones.

» DO NOT combine Trex Select decking with other Trex

decking products. Trex Select boards are thinner than

Transcend and Enhance boards.

Railing (Including ADA Handrail):

» First, pick the railing style you want.

» Calculate your spanning based on the railing you chose.

» Determine the number of balusters you will need based

on the railing you chose.

NOTE:

For post placement on stairs, it is VERY

IMPORANT to plan your post spacing based on

the length of the rail and angle of the stairs. For

nominal 6' and 8' stair rail lengths, stair post

spans (measured horizontally) will be less than 6'

or 8' due to the angle of the stairs.

NOTE: Trex Transcend and Select horizontal railings are

made to be installed at maximum of 6' (1.83 m) or 8'

(2.44 m) on center (depending upon type of railing you

choose). Those railings are not true 6' (72") or 8' (96") in

length. Trex Signature railing and Rod Rail are made to be

installed at maximum 6' or 8' CLEAR SPAN

BETWEEN POSTS.

» Determine post locations prior to installing any

decking. In most cases, posts are usually installed

before decking is installed.

» Conﬁrm with your local building ofﬁcial if ADA

Handrail is required, and if so plan spanning for posts

accordingly to allow for attachment of Trex ADA

Handrail. ADA Handrail requires a span of

6' OC for posts.

» Grill placement: A good recommendation to help

prevent damage to your railing is to not have a grill too

close to your railing. Allow for ample airspace

(6" or more is recommended) between the back/sides

of your grill to help prevent charring or staining to the

railing.

Refer to www.trex.com to view detailed install instructions

for Transcend, Select, or Signature railing.

Trex Lighting:

» Plan locations of lights, power supply, timer, and

dimmer. These should be accessible for service if

necessary.

» Install wiring before decking and railing have been

installed.

» DO NOT run wires between joists and deck boards.

Refer to www.trex.com to view detailed Trex lighting

instructions.

Trex

RainEscape

Deck Drainage System:

» Plan ahead for deck layout to allow for proper

placement of Trex RainEscape within the joist system.

» Make sure joists are straight and square.

See www.trex.com for more information on Trex

RainEscape recommendations and installation. Trex

RainEscape is manufactured and distributed by Dri-Deck

Enterprises, LLC, under a trademark license with Trex

Company, Inc.

Installing Hot Tubs, Planters, and Seating:

» Plan ahead proper joist spanning if required (this is

especially important if installing a hot tub).

» Refer to page 33 for Trex Decking Span Chart for

speciﬁc loads.

Call 1-800-BUY-TREX for detailed questions.

Planning Ahead

*DeckProtect

is a registered trademark of Inﬁnite Heat Solutions.

PLANNING AHEAD

Installing Fireplaces and/or Fire Pits With Trex

Decking:

» Determine if ﬁre will be gas or wood burning.

(NOTE: Most ﬁre pits shown in Trex images are gas

burning.)

» For gas, the ﬁre pit is installed by cutting around the

Trex decking. It is not to be installed on top of Trex

decking. A ﬁre-resistant material is installed under

the ﬁre pit and a protective “wall" made from stone or

other ﬁre-resistant material is installed to hold ﬁre pit

in place and also protect the decking from heat.

» For wood, ﬁre pits are not recommended on top

of Trex decking unless using a product called

DeckProtect

®*

. Wood-burning ﬁre pits can damage

the decking due to extreme heat from the bottom of

the ﬁre pit and/or burning embers “shooting" onto the

decking. DeckProtect

was tested on all Trex decking

and there were no issues with burning of the decking

surface when placed directly under a standard size

portable ﬁre pit along with the accompanying rack

(NOTE: Rack is not available for all sizes, so check

with manufacturer ﬁrst for veriﬁcation). Trex does

recommend that the DeckProtect

padding/rack

be moved from time to time for general cleaning

underneath. It should be noted that even when using

DeckProtect

, burning embers could “shoot" beyond

the protective mat and burn the deck.

For more information about this product, please

visit their website at www.deckprotect.net or call

1-800-BUY-TREX. DeckProtect

is a registered trademark

of Inﬁnite Heat Solutions.

Installing a Pergola on Trex Decking:

» Keep in mind that if you are planning to install a Trex

Pergola™ on your deck, you will need access to the

underside of the deck. Trex Pergola mounts with a

10" x 10" (254 mm x 254 mm) aluminum plate on the

underside of the deck, creating a clamping effect on

both the top and bottom of the deck for maximum

strength. If installed, water barriers and any under

deck coverings will have to be removed to properly

install the pergola posts.

» You need to consider the location of your pergola

posts with respect to joists. However, you do not have

to mount your plates between joists. It is possible to

place blocks on the bottom of the joists and mount

the Trex Pergola brackets through the blocks.

Trex

Pergola™ products are manufactured and sold by Home &

Leisure, Inc., d/b/a/ Structureworks Fabrication under a Trademark

License Agreement with Trex Company, Inc. A 25-year Limited

Warranty is provided by manufacturer.

Installing Trex

Spiral Stairs™:

» Refer to www.trexspiralstairs.com for detailed

information on how to plan and install Trex Spiral

Stairs.

Trex

Spiral Stairs™ are manufactured and sold by M. Cohen

and Sons, Inc., d/b/a The Iron Shop, under a Trademark License

Agreement with Trex Company, Inc. A 25-year Limited Warranty is

provided by manufacturer.

Installing Trex

Outdoor Kitchens™:

» Refer to trex-outdoorkitchens.com for detailed

information on how to install Trex Outdoor Kitchen

products.

Trex

Outdoor Kitchens

™

is manufactured and sold by

CT Acquistions LLC., under a Trademark Agreement

with Trex Company, Inc. A Limited Warranty is provided

by the manufacturer.

Planning Ahead/continued

NOTE: You can always reference the Design

Tools Section on www.trex.com for additional

planning ahead aids.

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

DECKING

TREX

DECKING & FASCIA

XX = COLOR PREFIX:

IM Island Mist

TT Tiki Torch

HG Havana Gold

SR Spiced Rum

LR Lava Rock

GP Gravel Path

RS Rope Swing

TH Tree House

VL Vintage Lantern

FP Fire Pit

PG Pebble Grey

WG Winchester Grey

SD Saddle

WB Woodland Brown

MB Madeira

FW Foggy Wharf

RH Rocky Harbor

TS Toasted Sand

CB Coastal Bluff

SC Sunset Cove

CS Clam Shell

BD Beach Dune

SD Saddle

1" Square-Edge Board

Actual dimensions:

Transcend & Enhance: .94 in x 5.5 in x 12 ft / 16 ft / 20 ft

(24 mm x 140 mm x 365 cm / 487 cm / 609 cm)

Select: .82 in x 5.5 in x 12 ft / 16 ft / 20 ft

(20 mm x 140 mm x 365 cm / 487 cm / 609 cm)

1 x 6 x 12' Transcend Tropicals

1 x 6 x 16' Transcend Tropicals

1 x 6 x 20' Transcend Tropicals

1 x 6 x 12' Transcend Earth Tones

1 x 6 x 16' Transcend Earth Tones

1 x 6 x 20' Transcend Earth Tones

1 x 6 x 12' Enhance Basics

1 x 6 x 16' Enhance Basics

1 x 6 x 20' Enhance Basics

1 x 6 x 12' Enhance Naturals

1 x 6 x 16' Enhance Naturals

1 x 6 x 20' Enhance Naturals

7/8 x 6 x 12' Select

7/8 x 6 x 16' Select

7/8 x 6 x 20' Select

1 x 6 x 12' Transcend Tropicals

1 x 6 x 16' Transcend Tropicals

1 x 6 x 20' Transcend Tropicals

1 x 6 x 12' Transcend Earth Tones

1 x 6 x 16' Transcend Earth Tones

1 x 6 x 20' Transcend Earth Tones

1 x 6 x 12' Enhance Basics

1 x 6 x 16' Enhance Basics

1 x 6 x 20' Enhance Basics

1 x 6 x 12' Enhance Naturals

1 x 6 x 16' Enhance Naturals

1 x 6 x 20' Enhance Naturals

7/8 x 6 x 12' Select

7/8 x 6 x 16' Select

7/8 x 6 x 20' Select

1 x 8 x 12' Transcend Tropicals

1 x 8 x 12' Transcend Earth Tones

1 x 8 x 12' Enhance Basics

1 x 8 x 12' Enhance Naturals

1 x 8 x 12' Select

1 x 8 x 12' Universal White

1 x 12 x 12' Transcend Tropicals

1 x 12 x 12' Transcend Earth Tones

1 x 12 x 12' Enhance Basics

1 x 12 x 12' Enhance Naturals

1 x 12 x 12' Select

1 x 12 x 12' Universal White

2 x 4 x 16' Transcend Tropicals

2 x 6 x 12' Transcend Tropicals

2 x 6 x 16' Transcend Tropicals

2 x 6 x 20' Transcend Tropicals

2 x 6 x 12' Select

2 x 6 x 16' Select

2 x 6 x 20' Select

XX010612TS01

XX010616TS01

XX010620TS01

XX010612T2S01

XX010616T2S01

XX010620T2S01

XX010612E2S01

XX010616E2S01

XX010620E2S01

XX010612E2S01

XX010616E2S01

XX010620E2S01

XX010612SS01

XX010616SS01

XX010620SS01

XX010612TG01

XX010616TG01

XX010620TG01

XX010612T2G01

XX010616T2G01

XX010620T2G01

XX010612E2G01

XX010616E2G01

XX010620E2G01

XX010612E2G01

XX010616E2G01

XX010620E2G01

XX010612SG01

XX010616SG01

XX010620SG01

XX010812TS01

XX010812T2S01

XX010812E2S01

XX010812SS01

WW010812ES01

XX011212TS01

XX011212T2S01

XX011212E2S01

XX011212SS01

WW011212ES01

XX020416TS01

XX020612TS01

XX020616TS01

XX020620TS01

XX020612SS01

XX020616SS01

XX020620SS01

IM, TT, HG, SR, LR

GP, RS, TH, VL, FP

CS, BD, SD

FW, RH, TS, CB, SC

PG, WG, SD, WB, MB

IM, TT, HG, SR, LR

GP, RS, TH, VL, FP

CS, BD, SD

FW, RH, TS, CB, SC

PG, WG, SD, WB, MB

IM, TT, HG, SR, LR

GP, RS, TH, VL, FP

CS, BD, SD

FW, RH, TS, CB, SC

PG, WG, SD, WB, MB

WOOD GRAIN WHITE

IM, TT, HG, SR, LR

GP, RS, TH, VL, FP

CS, BD, SD

FW, RH, TS, CB, SC

PG, WG, SD, WB, MB

WOOD GRAIN WHITE

IM, TT, HG, SR, LR

PG, SD, WB, MB

1" Grooved-Edge Board

Actual dimensions:

Transcend & Enhance: .94 in x 5.5 in x 12 ft / 16 ft / 20 ft

(24 mm x 140 mm x 365 cm / 487 cm / 609 cm)

Select: .82 in x 5.5 in x 12 ft / 16 ft / 20 ft

(20 mm x 140 mm x 365 cm / 487 cm / 609 cm)

1" x 8" Fascia

Actual dimensions:

Transcend, Enhance, Select, Universal White:

.56 in x 7.25 in x 12 ft (14 mm x 184 mm x 365 cm)

1" x 12" Fascia

Actual dimensions:

Transcend, Enhance, Select, Universal White:

.56 in x 11.375 in x 12 ft (14 mm x 288 mm x 365 cm)

2" Square-Edge Board

Actual dimensions:

Transcend 2x4: 1.3 in x 3.4 in x 16 ft

(33 mm x 86 mm x 487 cm)

Transcend & Select 2x6: 1.3 in x 5.5 in x 12 ft / 16 ft / 20 ft

(33 mm x 140 mm x 365 cm / 487 cm / 609 cm)

PROFILE DESCRIPTION

ITEM NUMBER COLORS

TREX HIDDEN FASTENING SYSTEM DESCRIPTION ITEM NUMBER

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

CONNECTCLIP

CLIPPAIL

GUNCLIP

UNIVSTARTCLIP

UNIVCONCLIP

DA00002

ROUTBIT

50 sq. ft. (4.6 sq. m) box

500 sq. ft. (46.5 sq. m) bucket

500 sq. ft. (46.5 sq. m) bucket with

collated pneumatic screws

400 sq. ft. (37 sq. m) bag

50 sq. ft. (4.6 sq. m) box

500 sq. ft. (46.5 sq. m) bucket

Router Bit

Connector Clip (stainless steel)

Gun Pail

Universal Starter Clip

Universal Fastener (glass-ﬁlled nylon)

Router Bit

DECKING

Decking and Fascia Recommended Fasteners

If any condition occurs which is attributable to the use of non-recommended fasteners, such condition shall not be covered under the Trex

Limited Warranty.

NOTES:

» D o not use any hidden fasteners that are plug based with Trex Enhance

proﬁles with scalloped bottom.

» 2-3/4" or 3" screws can be used with Trex 2x6 product.

» M uro T-Screw M-TX0300SEP listed above is approved for 2x6 decking

(can also be used with standard 1" (decking as listed above). This screw is

collated and can be used with Muro Auto Feed Screw Gun FDVL41 Speed

Driver. (NOTE: THIS IS NOT A COLOR-MATCH SCREW.)

» All decking products are approved for use with Trex Hideaway Hidden

Fasteners, thus all decking products can be routed according to our

instructions.

» S i mpson Strong-Tie Deck Drive DCU Composite Screw in collated

versions works with Quik Drive gun.

» * N o t for use with sleeper systems. Refer to FastenMaster

literature

for more information. Also, these are approved with Trex 2x6 decking

proﬁles.

» ** Fascia system screws listed above can only be used with composite

fascia proﬁles, and cannot be used with standard thickness

decking boards used as fascia. Use stainless steel screws near water

applications.

» C o ntact 1-800-BUY-TREX for Escapes fastener recommendations.

Trex recommends the use of two screws per joist.

All recommended screws are designed to be installed ﬂush with

decking surface. DO NOT countersink screws.

Use recommended stainless steel screws in any areas near bodies of

saltwater.

FastenMaster

TrapEase

3 and Cortex

are registered trademarks of

OMG, Inc.

Quik Drive

is a registered trademark and

Composi-Lok

™

is a trademark of Simpson Strong-Tie Company, Inc.

DeckFast

Cap-Tor

xd and HeadCote

Cap-Tor

xd are registered

trademarks of Starborn Industries Inc.

C-Deck Exterior Star Deck Composite Deck Screw is a product of Screw

Products Inc.

Phillips II Plus

is a registered trademark of Phillips Fasteners LLC.

SplitStop™ screws are a registered trademark of Titan Metal Werks, Inc.

Transcend

Enhance

(scalloped profile)

Select

RECOMMENDED FASTENERS

DECKING–HIDDEN FASTENERS

Trex Hideaway

Universal Hidden Fastener X X X

Trex Hideaway

Connector Clip X

TigerClaw

TC-G Hidden Fastener X X

Cortex

Concealed Fasteners* X X

Starborn

Pro Plug

System for PVC & Composite (Epoxy Coated &

Stainless) (2” are approved for sleeper & roof top applications only)

X X

Simpson Strong-Tie

Deck Drive™ DCU Composite Screw & DCU Screw

Plugs (Handdrive only & must also use Auto-Set Drive Bit)

X X

DECKING–COMPOSITE SCREWS

FastenMaster

TrapEase 3 Ultimate Composite Deck Screw X X X

Simpson Strong-Tie

Deck-Drive™ DCU Composite Screw

(Collated & Handdrive)

X X X

Quik Drive

Composi-Lok Deck Screw X X X

SplitStop™ Titan III Composite Screw X X X

Starborn® Cap-Tor® xd Epoxy Coated & Headcote® Stainless

(available collated for Muro CH7390 Driver**)

(2” are approved for sleeper & roof top applications only)

X X X

Screw Products C-Deck Exterior Star Drive Composite Deck Screw X X X

Phillips II Plus® Pozisquare X X X

Muro® T-Screw Torx Stainless Steel Screw - Collated

(TX0212SFD or M-TX0300SEP)

X X X

Kameleon™ GRKFasteners™ X

Transcend Enhance Select

RECOMMENDED

FASTENERS

FASCIA**

Cortex

Hidden Fastening System for Fascia

Starborn

Pro Plug

System for Fascia – Epoxy Coated & Stainless

Starborn

Deckfast

Fascia System – Epoxy Coated* & Headcote

Stainless

SplitStop™ Fascia Screw X

Simpson Strong-Tie

Fascia Board Screw X X X

FastenMaster

TrapEase

Fascia Fastener X X X

Minimum Fastener Size

SCREWS

Profile Length No.

1x6 2-1/2" or 2-3/4" #8, #10

2x6 2-3/4" or 3" #8, #10

DECKING

Trex

Fascia Installation Recommendations

Trex Fascia utilized around the perimeter of a deck must

be gapped with the same requirements as Trex decking

to allow for air flow and expansion/contraction of the

fascia.

When Using Approved Fascia Fasteners:

NOTE: The fasteners listed below can only be used with

1x8 or 1x12 fascia product, and cannot be used with

decking product that is being used as fascia trim or stair

risers.

See previous page for Trex-recommended Fascia

fasteners.

Always refer to manufacturing instructions ﬁrst for

installation methods. If instructions are not speciﬁc, refer

to the diagram below. Always remember to gap fascia

properly. A secondary glue is not required when using

these fasteners.

NOTE: Instructions below reﬂect the use of Trex-

recommended fascia fasteners. If using deck boards as

fascia, refer to the recommendations in next column on

this page.

TIPS:

» 10" rim joists (represented below unless noted)

allow for an easier and more aesthetically pleasing

installation.

» Miter cuts at butt joints and corners allow for a more

aesthetically pleasing installation (end-to-end

gapping rules still apply).

If Using Other Fasteners and/or Using Decking

Product in Fascia/Stair Riser Applications:

While Trex prefers the previous methods of

attachment, as these are the very best options, there

are also other recommendations that can be followed

for fascia or deck boards being used for fascia. Use

three Trex recommended composite decking screws

every 12". ALWAYS refer to manufacturer instructions

to ensure that recommended screws can be used for

fascia applications. The top screw should be placed 1"

from the top of the rim joist, the second screw in the

center of the rim joist, and the third screw 1" from the

bottom of the rim joist.

**IN ADDITION, also use a

weather-resistant,

construction-grade adhesive

(adhesives that work with

wood will work with Trex

products) as a SECONDARY

fastener when attaching

fascia. Remember to wipe

away any excess before it

dries or is allowed to drip on other Trex surfaces.

1"1"

Center

12"12"

Gap end-to-end

1/8" (>40°F)

3/16" (<40°F)

Abutting Gap

1/4 " (>40°F)

1/2" (<40°F)

1" x 8"

Fascia

(2" x 8"

rim joist)

18"18"

1" x 12"

Fascia

All Fascia profiles

when using

Non-Approved

Fascia Fasteners**

All Fascia profiles

when using

Non-Approved

Fascia Fasteners**

Miter Cut

1/8" (>40°F)

3/16" (<40°F)

**Weather-resistant

Adhesive

NOTE: English measurements are shown. Convert to metric measurements if necessary.

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

Decking

Fascia

Decking

Fascia

Install fascia UNDER decking

edges/ends. This will provide

protection to the fascia/

framing seam as well as

optimize the aesthetics of

the installation.

Do Not install fascia in the

method shown here. The

fascia board must be

attached fully to the rim

joist and cannot run parallel

to the decking surface.

DECKING

Framing and Fastening Tips

Fastening Tip for Trex Escapes,

Trex Transcend, Trex Enhance,

and Trex Select

NOTE: When using pneumatic or battery-operated

equipment, adjust the pressure so that you only

shoot the head of the screw to be ﬂush with the

board’s cap. DO NOT shoot the fastener head

completely through the shell.

Trex Products Near Low-E Windows

Low-E glass reﬂects more sunlight. It has been

observed that the extra reﬂectivity, combined with

any concavity in the glass, can act like a concave

mirror. This mirror effect concentrates sunlight

onto outdoor objects, including that of decking and

railing. This can result in an extreme amount of heat

concentrated on areas of the decking surface. This

can sometimes char the decking surface or cause

the decking to slightly bow.

Clean Cut Boards

It is recommended that boards be clean cut on both

ends a minimum of 3/16" (5mm).

Composite decking is a great alternative to traditional

wood decking. When building your deck and railing,

it is recommended that code-approved structural

material be used as the framing and joists. One

option is using Trex Elevations steel deck framing.

Refer to www.trex.com for more information on

Trex Elevations. Check your local building codes

for restrictions. Trex decking cannot be used for

structural applications. Do not attach Trex decking

directly to any solid surface or watertight system.

In most cases, install

fasteners at a 90° angle

(perpendicular to the

board).

At board ends on the

deck's edge, you can

install screws placed

perpendicularly at the

recommended distance,

at minimum of 1" (25mm)

from the board end and

edge, without splitting the

board.

For butt joints, where

boards meet over a

single joist, add a 2" x 4"

“nailer" board at the butt

joint. This allows screw-in

at 90 degrees and allows

fasteners to be used at

end of each board.

Dock Applications

Trex decking contains no materials that will

harm marine life and is safe for the environment.

As long as dock is in intermittent contact with

water, i.e., splashing and not in continuous direct

contact with water, the durability of the Trex

decking should not be affected.

For docks, a 3/8" (10mm) width-to-width gap

between boards is recommended to allow for

increased drainage due to increased contact with

water. In addition, stainless steel fasteners should

be used. If there is sufﬁcient contact between the

dock and gasoline, grounding of the dock is also

recommended.

Special Patterns

When planning a unique pattern, you will need to adjust the framing to support the surface pattern. Many

decks are designed to take advantage of angles, as shown below.

Herringbone Pattern Tile PatternPicture Frame Pattern

3/16" (5mm)

DECKING

Rooftop and Sleeper Deck Systems – Pressure-Treated Framing

» It is recommended that building-code approved

structural material be used as the supports.

» This system should not be allowed to ﬂoat. It must

be attached in a manner that secures the framing/

system.

» The sleeper system must be level and have no

uneven undulations. Any uneven areas of the

substructure will transfer to the Trex decking,

resulting in uneven decking.

» Trex, when used with a sleeper system, must be

supported below its entire length. If using in a

rooﬁng application, the supports must run the

direction of the pitch of the roof to facilitate proper

drainage. Sleeper should be placed perpendicular to

the deck board orientation.

» For commercial applications, consult a local building

code ofﬁcial for speciﬁc requirements.

» If installing decking at an angle, decrease spans

4" (100 mm) for each of the above. (12" (305 mm)

for residential and 8" (204 mm) for commercial.)

» For sleeper systems where small debris (pine

needles, leaves, sand, dirt) can accumulate either

between or under deck boards, a minimum of 1-1/2"

(38mm) height is allowable. Trex recommends

the use of Trex Universal Hidden Fasteners or 2"

Starborn Cap-Tor

xd - Epoxy Coated screws.

NOTE: Trex recommended composite decking

screws are too long when using 1-1/2" (38 mm)

height as this will penetrate through the sleeper.

For areas with the potential for debris buildup,

a minimum 3-1/2" (89 mm) or greater height is

recommended to allow the debris to be removed

along with the use of either Trex Universal Hidden

fasteners or any Trex recommended screws.

» Always consult your local building code authority for

proper details on roof and railing installation to the

roof structure if required.

» Any deviation from these recommendations could

result in voiding of the Trex warranty.

A sleeper system is a substructure between a solid surface and Trex decking. Drainage, access, and airﬂow are

critical. Water must be able to ﬂow through and away from the deck. For repairs and removal of debris, joist system

access may be necessary.

Residential = 16"

Commercial = 12"

1/2" Max.

Overhang

Min. 1-1/2"

Min.

1-1/2"

3/16" (All Temps)

1/8

" (>40°F)

3/16" (<40°F)

1/8" (>40°F)

3/16" (<40°F)

1/4" (>40°F)

1/2" (<40°F)

NOTE: English measurements are shown.

Convert to metric measurements if necessary.

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

DECKING

Metal Framing Requirements and Gapping

Perimeter

joists

Adjust end

span framing

per manufacturers

requirments

Adjust end

span framing

per manufacturers

requirements

Double joist

spacing per

manufacturers

requiremenrs

Double joist

spacing per

manufacturers

requirements

13mm

max. overhang

Gap decking

width-to-width

5mm (All Temps)

Gap decking

end-to-end

3mm (>4°C)

5mm (<4°C)

Two screws

per joist

NOTES:

» When using an aluminum framing system or

other type of metal for sleeper systems, follow

manufacturer's instructions for proper installation.

» Depending on type of structure being used,

different types of fasteners must be used for

attachment.

» When using screws to attach decking to framing,

use two screws per every joist.

NOTE: Metric measurements are shown.

Convert to US measurements if necessary.

DECKING

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

At a 60° angle, maximum

joist spanning is 2"

(51 mm) less than listed in

the chart below.

60°

Perpendicular to joists.

See chart below.

90°

At a 45° angle, maximum

joist spanning is 4"

(102 mm) less than listed

in the chart below.

45°

At a 30° angle, maximum

joist spanning is 1/2 of

the distance listed in the

chart below.

30°

Code Compliance

Joist Spanning for Decking

Trex decking meets all applicable national model

building codes. The joists must be spaced on center

according to the chart below. Be sure that joists are

level and plumb. Trex decking must span at least three

joists.

For heavy items such as hot tubs, planters,

etc., consult a local building engineer or inspector

for span recommendations. If you want to minimize

the appearance of joists through the spaces between

boards, paint the top of your joists black.

Code Listings

Trex complies with major model building codes and

has been evaluated by the International Code Council

evaluation service.

For a Safety Data Sheets (SDS), please visit

www.trex.com.

Adjust Joist Spanning to Accommodate

Angled Decking Patterns

Trex Decking Span Chart (on center)

Residential Decks, Light Duty Docks,

Residential/Day Care Playground

Commercial Decks,

Boardwalks and Marinas

Decking Loading 100 psf = 4.8 kN/m2 100 psf = 4.8 kN/m2 200 psf = 9.5 kN/m2

1" (25 mm) Boards (including Porch),

and .875" (22 mm) Select Boards

16" (406 mm)

16" (406 mm) 12" (305 mm)

2" x 6" (51 mm x 152 mm) Boards 24" (610 mm) 24" (610 mm) 16" (406 mm)

Trex Railing Span Chart

Maximum Railing Span for all Applications

Transcend, Select railing, and

Trex Signature railing

96" on center (2438 mm) for Transcend, 72" on center (1829 mm) for Select,

96" (2438 mm) clear span for Trex Signature

DECKING

1/4" – 1/2"

(6 mm – 13 mm)

3/16”

(5 mm)

Gapping and Overhang

You must gap Trex decking both end-to-end and

width-to-width. Gapping is necessary for drainage and

the slight thermal expansion and contraction of Trex

decking boards. Gapping also allows for shrinkage of

the wood joist system.

» ALWAYS follow Trex-recommended gapping

guidelines.

» Maximum allowable perpendicular overhang for all

Trex decking is 1/2" (13 mm).

» All decks require air circulation to keep them dry and

looking good. To improve air ﬂow, leave openings

under the decking or increase gapping to 3/8"

(10 mm).

End-to-End/End-to-Width

Gap Trex decking end-to-end, based upon the

temperature at installation.

See chart at left.

For fastening tips, see page 30.

Abutting Solid Objects

When decking is abutting a wall, you must also gap it

1/4"–1/2" (6–13 mm) depending on the temperature at

installation. See chart at left.

Width-to-Width

The minimum required width-to-width gapping is

3/16" (5 mm). This is allowed for both hot and cold

weather installations. For docks and heavily wooded

areas, Trex recommends a 3/8" (10 mm) gap. No

gapping should ever exceed 1/2" (13 mm).

*Temperature at installation.

End-to-End/End-to-Width and Abutting Gap

End-to-End/

End-to-Width

Abutting Gap

3/16" (5 mm)

Width-to-Width Gap

1/8 " – 3/16"

(3 mm – 5 mm)

Above 40°F* (4.5°C)* 1/8" (3 mm) 1/4" (6 mm)

Below 40°F* (4.5°C)* 3/16" (5 mm) 1/2" (13 mm)

When you use the recommended hidden fasteners,

the placement of the hidden fastener establishes the

designated gap size.

When installing fascia, gapping rules must apply.

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

1/8" – 3/16"

(3 mm – 5 mm)

DECKING

Important Notes Before Installing Trex

Decking

3/16" (5mm)

It is recommended to clean cut boards on both

ends a minimum 3/16" (5mm).

To ensure an appealing mix of color tones,

mix and match all boards prior to installation.

Pre-drill using 1/8" bit

1" (25mm)

If installing in localities prone to large

temperature shifts within a 24-hour period,

and installing Trex Universal Hidden Fasteners,

predrill and toenail a screw (use same screw

used in hidden fasteners) at an angle in groove

at both ends (at least 1" (25mm) from board

end) and center of each board.

Routing Square Edge Boards for Trex Hideaway

Hidden Fasteners

NOTE: All Trex square edge proﬁles, either 1x6 or 2x6,

can be routed.

Using a Trex routerbit with standard router:

1. Rout from bottom side of board.

2. Rout the entire length of the board, or at every

intersection where board is over support joists.

1/8" (>40°F)

3/16" (<40°F)

3mm (>4.5C)

5mm (<4.5C)

30mm

Abutted Board Attachment Requirements

Metal Framing

NOTE: Hidden Fasteners MUST be used at every joist.

NOTE: Use a drill (with adjustable clutch and torque)

and adjust these settings if necessary to ensure screw

is seated correctly in fastener. DO NOT countersink the

screw head into the fastener. Screw head should be

ﬂush with the top of the fastener.

NOTE: Optional - Gap joist framing 1-1/8" to allow for

water drainage.

HOW TO INSTALL DECKING

Installing Trex Transcend

, Enhance

, Select

Deckboards

1/4" >40°F*

1/2" <40°F*

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

NOTE: Use scrap piece of decking to help hold fastener in

place while attaching.

*6mm >4˚C 13mm <4˚C

HOW TO INSTALL DECKING

Installing Trex Transcend

, Enhance

, Select

Deckboards/

continued

1" (25mm)

Installing Last Deck Board

(Square-Edge Board Recommended)

Installing Trex Escapes

Boards/continued

with Trex Hideaway

Universal Hidden Fasteners

1/4" >40°F*

1/2" <40°F*

Route one side of square-edge board to use with hidden

fasteners.

TIP: Use a recommended hidden fastener screw and

plug for last board installation.

Fascia screws supplied by installer (1 x 8 fascia shown).

NOTE: Refer to page 15 for detailed fascia attachment

instructions.

*6mm >4˚C 13mm <4˚C

HOW TO INSTALL DECKING

Installing Trex Escapes

Boards/continued

with Trex Hideaway

Universal Hidden Fasteners

Pre-drill

1"(25mm)

Use same screw as supplied with hidden fastener.

NOTE: Install at both ends and center of board.

Pre-drill

1"(25mm)

Use same screw as supplied with hidden fastener.

NOTE: Install at both ends and center of board.

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

HOW TO INSTALL DECKING

1" (25mm)

Installing Last Deck Board (Square-Edge Board Recommended)

Route one side of square-edge board to use with hidden

fasteners.

Fascia screws supplied by installer (1 x 8 fascia shown).

Installing Trex Escapes

Boards/continued

with Trex Hideaway

Universal Hidden Fasteners

Replacing Trex Boards (Transcend

, Enhance

, Select

, Escapes

)

Installed with Trex Hideaway

Universal Fasteners

New board at an angle

Existing Deck

Insert Fasteners

HOW TO INSTALL DECKING

Stringer

1” x 8" Riser

11" min. depth

1/4" - 3/8" gapping

Fasten treads to

all stringers

3/4" max. overhang

See chart below

Riser removed for clarity

36" minimum width – 4 stringers are required

Above 36" width – 5 stringers are required

Spanning Requirements for Trex

Stairs

Note: English measurements are shown. Convert to metric measurements if necessary.

Stairs

Stairway Detail

» Stair treads built with Trex meet requirements of

the major national building codes. Consult your local

municipality for speciﬁc requirements.

» Fasten stair treads continuously across at least four

stringers.

» See chart (at right) for center-to-center spacing of

proﬁles.

» Dress the sides of the stringers and risers with trim or

Trex fascia for a ﬁnished look.

» When installing risers, use two screws per every

stringer.

» Fascia fasteners can only be used if fascia boards

are being used for risers. If deck boards are used,

recommended composite deck screws must be used

(glue is not required for this application).

» Most model building codes require the stair treads to

be constructed under the following requirements:

› Stairways must be at least 36" wide*

› Stair treads must be at least 11" deep

» Gapping between Trex boards on stair treads must be

1/4"–3/8".

» The overhang of the stair tread is not to exceed 3/4".

* For railings that are installed directly over stair treads, the stair

treads may need to be larger than 36" wide. Refer to local building

code regulations for details prior to installing stairs and railings.

NOTES:

» Trex rails meet all major building codes for use as a

guardrail system. Local municipalities may require a

graspable handrail on stairways. Check with your local

building code ofﬁcial for local requirements. See Trex

ADA Handrail System in the Trex product catalog.

» Trex Porch Boards should not be used for stair applica

tions. Use square-edge composite decking boards and

manually rout these where needed to allow for use with

hidden fasteners.

Maximum Spacing on Center of Stair Stringer

Transcend 1" x 6"

12"

Select, Enhance (scalloped bottom),

and Escapes 1" x 6"

Transcend & Select 2" x 6"

12"

HOW TO INSTALL DECKING

1/4" >40°F*

1/2" <40°F*

Rout one side of board (last stair tread).

Installing Trex

Stair Treads

Installed with Hidden Fasteners

NOTE: Use square-edge, composite decking boards and manually route these on required sides to allow for use with

hidden fasteners.

*6mm >4˚C 3mm <4˚C

WARRANTIES

For the term set forth below, Trex Company, Inc. (hereinafter “Trex”)

warrants to the original end-user purchaser (the “Purchaser”) that

Trex Transcend

decking, porch or fascia, Trex Enhance

decking or

fascia, Trex Select

decking or fascia or Trex Universal Fascia, as the

case may be (the “Product”) will perform, under normal use and

service conditions, as follows:

Term of Warranty: The term of this warranty shall begin on the

date of original purchase, and shall end (1) twenty-ﬁve (25) years

thereafter for a residential application of the Product, and (2) ten

(10) years thereafter for a commercial application of the Product.

Notwithstanding the foregoing, the term of this warranty for

Transcend Product used as outdoor cladding shall be twenty-ﬁve

(25) years for both a residential application and a commercial

application.

Residential/Commercial Application: For purposes of this

warranty, a “residential application” shall refer to an installation

of the Product on an individual residence, and a “commercial

application” shall refer to any installation of the Product other than

on an individual residence.

Fade Resistance: The Product shall not fade in color from light and

weathering exposure as measured by color change of more than 5

Delta E (CIE) units.

The Product is designed to resist fading. No material is fade proof

when exposed to years of UV exposure and the elements. The

Product is designed to resist fading, and will not in any event fade

by more than 5 Delta E (CIE) units.

Stain Resistance: The Product shall be resistant to permanent

staining resulting from spills of food and beverage items including

ketchup, mustard, salad oils, tea, wine, coffee, fruit punch, barbeque

sauce, grease, sodas and other food and beverage related items

that would typically be present on a residential deck, or mold and

mildew naturally occurring in the environment, provided that such

substances are removed from the Product with soap and water or

mild household cleaners within one (1) week of exposure of the

food or beverage to the surface or ﬁrst appearance of the mold and

mildew.

Notwithstanding the foregoing, Trex does not warrant that the

Product is stain-proof, and does not warrant stain resistance

resulting from spilled or otherwise applied food and beverage

substances which are not properly cleaned as provided above

within one (1) week of exposure. In addition, materials not covered

in the stain resistant warranty include abrasive compounds of

acidic or basic pH, paints or stains, strong solvents, metallic rust or

other abnormal deck use items, and non-food and non-beverage

substances, including but not limited to, biocides, fungicides, plant

food, or bactericides. Mold and mildew can settle and grow on any

outdoor surface, including this Product. You should periodically

clean your deck to remove dirt and pollen that can feed mold and

mildew. This warranty does not cover mold and mildew which is

not properly cleaned as provided above within one (1) week of ﬁrst

appearance.

Standard Trex Company Limited Warranty: This warranty is

in addition to the standard Trex Company Limited Warranty that

applies to all Trex products.

Transferability: With respect to a residential application, this

warranty may be transferred one (1) time, within the ﬁve (5) year

period beginning from the date of original purchase by the Purchaser,

to a subsequent buyer of the property upon which the Trex products

were originally installed. With respect to a commercial application,

this warranty is freely transferable to subsequent buyers of the

property upon which the Trex products were originally installed.

EXCLUSIONS FROM WARRANTY COVERAGE:

Exposure to Heat: Direct or indirect contact with extreme heat

sources (over 275 degrees) may cause fading and may damage

the surface of the Product, and any effects of such exposure are

expressly excluded from coverage under this warranty.

Surface Damage: Never use metal shovels or sharp-edged tools

to remove snow and ice on the surface of the Product. If the

surface of the Product is damaged or punctured, this warranty will

be voided.

Paint or Other Materials Applied to the Product: If paint or

other coating materials are applied to the Product, this warranty

will be voided.

Railing: This warranty does not cover Trex Transcend

Trex Enhance

or Trex Select

railing components.

Other Exclusions: This warranty shall not cover any condition

attributable to: (1) improper installation of the Product and/or

failure to abide by Trex’s installation guidelines, including but not

limited to improper gapping; (2) use of the Product beyond normal

use or service conditions, or in an application not recommended

by Trex’s guidelines and local building codes; (3) movement,

distortion, collapse or settling of the ground or the supporting

structure on which the Product is installed; (4) any act of God (such

as ﬂooding, hurricane, earthquake, lightning, etc.); (5) improper

handling, storage, abuse or neglect of the Product by Purchaser,

the transferee or third parties; (6) any fading or staining not on the

walking surface of the Product (i.e., the underside or the ends of

the Product); or (7) ordinary wear and tear.

Procedure for Making a Claim under this Warranty

In order to make a claim under this warranty, Purchaser must do

the following:

1. If the Purchaser is making a claim relating to the warranty on

stain resistance, Purchaser must do as follows:

TREX TRANSCEND

, TREX ENHANCE

, TREX

SELECT

AND TREX

UNIVERSAL FASCIA

LIMITED FADE & STAIN WARRANTY

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

WARRANTIES

(a) Purchaser must try to clean the affected area of the deck by

using the cleaning procedures described above within one (1)

week of exposure of the food or beverage to the Product or ﬁrst

appearance of the mold and mildew.

(b) If the affected area remains reasonably unsatisfactory after

Purchaser has tried these cleaning procedures, then Purchaser

must have the affected area of the deck professionally cleaned at

Purchaser’s expense.

the professional cleaning, Purchaser may make a claim under this

warranty, provided that such claim is made within thirty (30) days

after the professional cleaning.

2. To make a claim under this limited warranty, Purchaser, or the

transferee, shall send to Trex, within the warranty period referred

to above, a description and photographs of the affected area of the

Product, proof of purchase, and if the claim relates to the warranty

on stain resistance, proof of compliance with paragraph 1. above, to

the following address:

Trex Company, Inc.

Customer Relations

160 Exeter Drive

Winchester, VA 22603-8605

3. Upon conﬁrmation by an authorized Trex representative of a

valid claim hereunder, Trex’s sole responsibility shall be, at its

option, to either replace the affected item or refund the portion of

the purchase price paid by Purchaser for such affected item (not

including the cost of its initial installation). Replacement material

will be provided that is as close as possible in color, design and

quality as the replaced material, but Trex does not guarantee an

exact match as colors and design may change.

4. If a valid warranty claim hereunder is made during years eleven

(11) through twenty-ﬁve (25) after the original purchase for a

residential application, recovery will be prorated. If Trex is providing

replacement materials, it may elect to replace the percentage listed

below of boards otherwise meeting the requirements for a claim,

or if it is refunding the purchase price, it may elect to refund the

percentage listed below of the purchase price of boards otherwise

meeting the requirements for a claim.

YEAR OF

WARRANTY CLAIM

PERCENTAGE

RECOVERY

11 80%

12 80%

13 80%

14 60%

15 60%

16 60%

17 40%

18 40%

19 40%

20 20%

21 20%

22 20%

23 10%

24 10%

25 10%

5. TO THE FULLEST EXTENT PERMITTED UNDER THE LAW,

THIS WARRANTY SHALL NOT COVER AND TREX SHALL NOT

BE RESPONSIBLE FOR COSTS AND EXPENSES INCURRED

WITH RESPECT TO THE REMOVAL OF AFFECTED PRODUCT

OR THE INSTALLATION OF REPLACEMENT MATERIALS,

INCLUDING BUT NOT LIMITED TO LABOR AND FREIGHT.

No person or entity is authorized by Trex to make and Trex shall

not be bound by any statement or representation as to the quality

or performance of Trex products other than as contained in this

warranty. This warranty may not be altered or amended except in

a written instrument signed by Trex and Purchaser.

TO THE FULLEST EXTENT PERMITTED UNDER THE LAW,

UNDER NO CIRCUMSTANCES WILL TREX BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER

SUCH DAMAGES ARE SOUGHT IN CONTRACT, IN TORT

(INCLUDING BUT NOT LIMITED TO NEGLIGENCE AND STRICT

LIABILITY) OR OTHERWISE, AND TREX’S LIABILITY FOR NON-

PERSONAL INJURY CLAIMS WITH RESPECT TO PRODUCTS

SHALL IN NO EVENT EXCEED THE REPLACEMENT OF SUCH

PRODUCTS OR REFUND OF THE PURCHASE PRICE, AS

DESCRIBED ABOVE.

Some States or Provinces do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation or

exclusion may not apply to you. This warranty gives you speciﬁc

legal rights, and you may also have other rights that vary from

State to State or Province to Province.

TREX TRANSCEND

, TREX ENHANCE

, TREX

SELECT

AND TREX

UNIVERSAL FASCIA

LIMITED FADE & STAIN WARRANTY/continued

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

WARRANTIES

Trex Company, Inc. (hereinafter “Trex”) warrants to the original

purchaser (“Purchaser”) that, for the period of time set forth in

the following sentence, under normal use and service conditions,

Trex

product (the “Product”) shall be free from material defects

in workmanship and materials, and shall not split, splinter, rot or

suffer structural damage from termites or fungal decay. The term

of such warranty shall be twenty-ﬁve (25) years from the date of

original purchase for a residential application, and ten (10) years

from the date of original purchase for a commercial application.

If a defect occurs within the warranty period, Purchaser shall

notify Trex in writing and, upon conﬁrmation by an authorized Trex

representative of the defect, Trex’s sole responsibility shall be, at its

option, to either replace the defective Product or refund the portion

of the purchase price paid by Purchaser for such defective Product

(not including the cost of its initial installation).

For purposes of this warranty, a “residential application” shall

refer to an installation of the Product on an individual residence,

and a “commercial application” shall refer to any installation of the

Product other than on an individual residence.

Notwithstanding the foregoing, (a), the term of the warranty

for the LED lights and housing for Trex Deck Lighting

shall

be seven (7) years, the term of the warranty for the LED lights

and housing for Trex Landscape Lighting

shall be ﬁve (5)

years, the term of the warranty for the dimmer, timer and

transformer for both shall be three (3) years, and the term of

the warranty for the motion controller for both shall be one

(1) year, in each case provided that a Trex transformer is used

(with no warranty on any components if a Trex transformer

is not used), and any other parts or accessories shall not

be warranted; (b) with respect to hardware for the Trex

Surroundings

gate (gate frame, hinges and screws), the term

of the warranty shall be ﬁve (5) years, (c) with respect to Trex

Decorative Balusters, the term of the warranty covering the

paint coating shall be ten (10) years, and shall be prorated

in the following manner: 100% replacement for the ﬁrst ﬁve

(5) years; and 50% replacement for the next ﬁve (5) years,

(d) the term of the warranty for Transcend Product used as

outdoor cladding shall be twenty-ﬁve (25) years for both a

residential application and a commercial application, and (e)

this warranty shall not apply to Trex Elevations

steel deck

framing, Trex Signature

aluminum railing and TrexTrim

(which each have separate warranties).

TO THE FULLEST EXTENT PERMITTED UNDER THE LAW, THIS

WARRANTY SHALL NOT COVER AND TREX SHALL NOT BE

RESPONSIBLE FOR COSTS AND EXPENSES INCURRED WITH

RESPECT TO THE REMOVAL OF DEFECTIVE PRODUCT OR THE

INSTALLATION OF REPLACEMENT MATERIALS, INCLUDING

BUT NOT LIMITED TO LABOR AND FREIGHT.

With respect to a residential application, this warranty may be

transferred one (1) time, within the ﬁve (5) year period beginning

from the date of original purchase by the Purchaser, to a subsequent

buyer of the property upon which the Product was originally

installed. With respect to a commercial application, this warranty

is freely transferable to subsequent buyers of the property upon

which the Product was originally installed.

To make a claim under this limited warranty, Purchaser, or the

transferee, shall send to Trex, within the warranty period referred to

above, a description of the claimed defect and proof of purchase, to

the following address:

Trex Company, Inc.

Customer Relations

160 Exeter Drive

Winchester, VA 22603-8605

Trex does not warrant against and is not responsible for any

condition attributable to: (1) improper installation of Product

and/or failure to abide by Trex’s installation guidelines, including

but not limited to improper gapping; (2) use of Product beyond

normal use and service conditions, or in an application not

recommended by Trex’s guidelines and local building codes; (3)

movement, distortion, collapse or settling of the ground or the

supporting structure on which Product is installed; (4) any act

of God (such as ﬂooding, hurricane, earthquake, lightning, etc.),

environmental condition (such as air pollution, mold, mildew, etc.),

staining from foreign substances (such as dirt, grease, oil, etc.), or

normal weathering (deﬁned as exposure to sunlight, weather and

atmosphere which will cause any colored surface to gradually fade,

chalk, or accumulate dirt or stains); (5) variations or changes in

color of Product; (6) improper handling, storage, abuse or neglect

of Product by Purchaser, the transferee or third parties; or (7)

ordinary wear and tear.

No person or entity is authorized by Trex to make and Trex shall not

be bound by any statement or representation as to the quality or

performance of Product other than as contained in this warranty.

This warranty may not be altered or amended except in a written

instrument signed by Trex and Purchaser.

TO THE FULLEST EXTENT PERMITTED UNDER THE LAW,

UNDER NO CIRCUMSTANCES WILL TREX BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER

SUCH DAMAGES ARE SOUGHT IN CONTRACT, IN TORT

(INCLUDING BUT NOT LIMITED TO NEGLIGENCE AND STRICT

LIABILITY) OR OTHERWISE, AND TREX’S LIABILITY FOR NON-

PERSONAL INJURY CLAIMS WITH RESPECT TO DEFECTIVE

PRODUCT SHALL IN NO EVENT EXCEED THE REPLACEMENT

OF SUCH PRODUCT OR REFUND OF THE PURCHASE PRICE,

AS DESCRIBED ABOVE.

Some States or Provinces do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation or

exclusion may not apply to you. This warranty gives you specic legal

rights, and you may also have other rights that vary from State to

State or Province to Province.

TREX

LIMITED WARRANTY

NOTE: Construction methods are always improving. Please refer to www.trex.com for the most up-to-date installation requirements.

NOTES

DECKING COLOR PALETTE

Woodland Brown

Select

Rope Swing

Transcend

Earth Tones

Clam Shell

Enhance

Basics

DECKING COLOR PALETTE

BROWNS

GREYS

REDS

Foggy Wharf

Enhance

Naturals

Rocky Harbor

Enhance

Naturals

Gravel Path

Transcend

Earth Tones

Pebble Grey

Select

Island Mist

Transcend

Tropicals

Winchester Grey

Select

Beach Dune

Enhance

Basics

Toasted Sand

Enhance

Naturals

Saddle

Enhance

Basics

Coastal Bluff

Enhance

Naturals

Saddle

Select

Tiki Torch

Transcend

Tropicals

Havana Gold

Transcend

Tropicals

Tree House

Transcend

Earth Tones

Spiced Rum

Transcend

Tropicals

Vintage Lantern

Transcend

Earth Tones

Lava Rock

Transcend

Tropicals

Fire Pit

Transcend

Earth Tones

Sunset Cove

Enhance

Naturals

Madeira

Select

BACK

decking: Transcend in Island Mist

FRONT

decking: Transcend in Havana Gold

railing:

Trex Signature

Rod Rail in Charcoal Black

FIND US ON

Visit trex.com or call 1-800-BUY-TREX

XKLTINGD2020

1219

FPO

, the Trex logo, Trex Transcend

, Trex Enhance

, Trex Select

, Trex Signature

, Trex Hideaway

Trex Elevations

, Trex

Outdoor Lighting™, Trex Blade™, Trex

Outdoor Kitchens™, Trex

Spiral Stairs™, Trex

RainEscapes

, Trex

Pergola

™

, TrexPro

Trex

CustomCurve

, Trex

LatticeWorks™ and Trex

Cornhole

™

are either federally registered trademarks, trademarks or trade dress of Trex Company, Inc.,

Winchester, Virginia or its licensees.